DeWalt 31-260X instruction manual Protection Contre LES Surcharges DU Moteur DU Tambour

Page 30

PROTECTION CONTRE LES SURCHARGES DU MOTEUR DU TAMBOUR

Le moteur du tambour est doté d’un bouton de réinitialisation du re- lais de surcharge. Si le moteur refuse de démarrer en raison d’une surcharge ou d’une faible tension, mettre les deux interrupteurs sur arrêt (OFF). Laisser refroidir le moteur pendant 3 à 5 minutes, puis ap- puyer sur le bouton de réinitialisation (A), Fig. 17B. Démarrer l’appareil.

VÉRIFICATION ET RÉGLAGE DU PARALLÉLISME DE LA TABLE AU TAMBOUR

A

Fig. 17B

REMARQUE : à sa sortie de l’usine, la table est parallèle au tambour. La distance (B), Fig. 18, devrait être la même d’avant en arrière, sur toute la largeur de la courroie d’alimentation. Mesurr l’épaisseur de la planche à plusieurs endroits dans le sens de la longueur et de la largeur pour être certain.

1.En guise de mise à l’essai, poncer une planche large (B), Fig. 19, (mesurant de préférence 305 mm [12 po] ou plus de large sur 610 mm [2 pi] de long) jusqu’à ce que toute sa surface soit aplanie, des deux côtés.

A.Pour procéder à une vérification rapide, tracer des lignes au crayon (C), Fig. 20, dans le sens de la largeur à plusieurs endroits le long de la planche. NE PAS

RÉGLER LA HAUTEUR DE LA TABLE.

B.Tourner la planche (en inverser les bouts) et la passer dans la ponceuse. Si la table de ponçage est réglée adéquatement, les lignes tracées disparaîtront. Si les lignes sont toujours visibles à gauche ou à droite de la planche, ajuster la hauteur de la table.

2.Utiliser une clé de 12,7 mm (1/2 po) pour tenir les boulons de nivellement, l’un deux étant illustré dans la Fig. 21 (E). Utiliser une clé hexagonale de 4,8 mm (3/16 po) (D) pour desserrer les boulons hexagonaux. Tourner les boulons de nivellement d’un pan

àla fois jusqu’à ce que la table soit parallèle au tambour.

REMARQUE : un tour d’un pan du boulon de nivellement fait monter ou baisser la table de 0,25 mm (0,010 po). Tourner le boulon de nivellement (E), Fig. 20, dans le sens horaire pour abaisser la table ou dans le sens antihoraire pour l’élever. Effectuer un ajustement égal des deux boulons de nivellement, et ce, dans la même direction.

Fig. 18

B

B

B

Fig. 19

C

Fig. 20

D

E

Fig. 21

RÉGLAGE DE L’ÉCHELLE DE HAUTEUR

1.Courir un morceau de bois par la ponceuse de tambour (fig. 22) finir un côté du conseil.

2.Utiliser un carré (A) fig. 23 pour mesurer l’épaisseur du bois.

3.Desserrer le boulon (B) fig. 24. Monter l’échelle ou en bas jusqu’à ce que le curseur montre 2 à l’épaisseur de conseil exacte qui a été mesurée dans l’ETAPE. Resserrer le boulon.

Fig. 22

B

A

Fig. 23

B

Fig. 24

30

Image 30
Contents 31-260X Table of Contents Important Safety InstructionsSafety Guidelines Definitions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEMotor Specifications Additional Specific Safety RulesPower Connections Grounding InstructionsMinimum Gauge Extension Cord All grounded, cord-connected machinesCarton Contents Functional DescriptionAssembly Assembly Tools RequiredAssembly Time Estimate HOW to Attach the Handwheel HOW to Attach and Level the Feed TableOperating Controls and Adjustments To Check and Adjust Tracking HOW to Raise the TableHOW to Check and Adjust the Feed Belt Tracking and Tension To Check and Adjust TensionHOW to Check and Adjust the Table Parallel to the Drum HOW to SET the Height ScaleDrum Motor Overload Protection HOW to Change the Drum Speeds and Replace the Drive Belt HOW to Remove and Replace the Drum Sanding BeltHOW to Remove and Replace the Feed Belt Feed Belt Motor Overload ProtectionFrequently Asked Questions What are the Maximum and Minimum Sanding Stock SIZES? Dust Collection RecommendationWhat Causes Burn MARKS? HOW do I Sand Multiple BOARDS?HOW do I Sand Boards Wider than 18? HOW to Increase Sanding Belt LifeTable Movement Troubleshooting Guide HOW do I GET STARTED?Timing Belt Tension Checking the Table Support PlateTroubleshooting Maintenance Checking the Lock NUT AdjustmentAligning Elevating Bolt Bushings Replacement Parts ServiceKeep Machine Clean Lubrication & Rust ProtectionFree Warning Label Replacement AccessoriesWarranty Service and RepairsLES Instructions Importantes DE Surete Mesures DE Sécurité DéfinitionsLA Proposition DE Californie Règles DE Sécurité Générales Lutilisation DE CET Outil PeutSpécifications DU Moteur Règles Spécifiques Additionnelles DE SûretéRaccordements Électriques Instructions DE Mise À LA TerreCordon DE Rallonge Mesur Minimum DE Corde D’EXTENSIONAVANT-PROPOS Description FonctionnelleContenus DE Boite Désemballage ET NettoyageLestimation DE Temps Dassemblee AssemblageOutils Nécessaires Pour L’ASSEMBLEE Assemblage DU SocleFixation DU Volant Fixation ET Mise DE Niveau DE LA Table D’ALIMENTATIONTAG Fixation DE L’INDICATEUR D’ALIMENTATION « SA » FonctionnementLoperation Controle DE LE ET LES Ajustements Comment Commencer ET Arreter LA MachineÉlévation DE LA Table Vérification ET Réglage DE L’ALIGNEMENTVérification ET Réglage DE LA Tension Protection Contre LES Surcharges DU Moteur DU Tambour Réglage DE L’ÉCHELLE DE HauteurRetrait ET Remplacement DE LA Bande Abrasive DU Tambour Retrait ET Remplacement DE LA Courroie D’ALIMENTATION Demande Frequemment AUX Questions Quels Facteurs Influent SUR LES Opérations DE PONÇAGE?Comment PUIS-JE Poncer Plusieurs PLANCHES? Quelles Sont LES Recommandations Pour LE DépoussiérageQU’EST-CE QUI Cause LES Marques DE BRÛLURE? Comment PUIS-JE Poncer LES Planches COLLÉES?PAR OÙ DOIS-JE COMMENCER? Ajourner LE Guide DE Depannage DE MouvementÉtape 1 Tension DE LA Courroie Crantée Étape 2 Vérification DE LA Plaque DE Fixation DE LA TableDepannage Entretien Étape 3 Vérification DE L’AJUSTEMENT DU CONTRE-ÉCROUÉtape 4 Alignement DES Bagues DE Boulon D’ÉLÉVATION Démarrage Impossible Inspection ET Remplacement DES BrossesGarder LA Machine Propre Lubrification ET Protection Contre LA RouilleGarantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNormas Generales DE Seguridad EL USO DE Esta Herramienta PuedeEspecificaciones DEL Motor Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraCordones DE Extensión Cordón DE Extensión DE Calibre MínimoPrologo Descripción FuncionalContenido DE Carton Desempaquetado Y LimpiezaEnsamblaje Herramientas DE Ensamblaje RequeridasEstimación DEL Tiempo DE Ensamblaje Cómo Instalar EL Volante Cómo Instalar Y Nivelar LA Mesa DE AlimentaciónArrancando Y Deteniendo LA Maquina OperaciónControles Y Ajustes Operacionales Cómo Conectar EL Indicador DE Alimentación SACómo Elevar LA Mesa Para Comprobar Y Ajustar LA TrayectoriaPara Comprobar Y Ajustar LA Tensión Cómo Configurar LA Escala DE Altura Protección Contra Sobrecarga DEL Motor DEL TamborCómo Comprobar Y Ajustar LA Mesa Paralela AL Tambor Cómo Quitar Y Reemplazar LA Banda DE Lijado DEL Tambor Cómo Quitar Y Reemplazar LA Banda DE Alimentación Hizo CON Frecuencia Preguntas ¿CÓMO Lijo LOS Bordes DE LAS TABLAS? ¿QUÉ Produce LAS Marcas DE QUEMADURA?¿CÓMO Lijo Varias TABLAS? ¿CÓMO Lijo LAS Tablas AHUECADAS, Curvadas O TORCIDAS?¿CÓMO Lijo Tablas MÁS Anchas QUE 457 MM 18? Posponga LA Guia DE Localizacion DE Fallas DE MovimientoPaso 1 Tensión DE LA Banda DE Distribución Paso 2 Inspección DE LA Placa DE Soporte DE LA MesaLocalizacion DE Fallas Maintenance Paso 3 Comprobación DEL Ajuste DE LA Tuerca DE SeguridadMantenimiento ServicioAccessories Póliza DE Garantía Identificación DelproductoExcepciones Your ACHIEVEMENT. OUR Tools

31-260X specifications

The DeWalt 31-260X is a powerful and versatile cordless drill that stands out in the competitive world of power tools. With its combination of robust performance, advanced features, and user-friendly design, it has become a favorite among both professionals and DIY enthusiasts alike.

One of the main features of the DeWalt 31-260X is its high-performance motor, which delivers impressive torque and speed to tackle a variety of materials and applications. The drill operates at multiple speed settings, allowing users to adjust the RPM according to their specific project needs. This feature is particularly useful when working with different materials, such as wood, metal, or plastic, ensuring optimal results with minimal effort.

The 31-260X also boasts a compact and lightweight design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. The ergonomic grip is designed for comfort and control, providing a secure hold that enhances precision during drilling and driving tasks.

In terms of battery technology, the DeWalt 31-260X is equipped with the brand's state-of-the-art lithium-ion batteries, which deliver extended run times and shorter charge times. This ensures that users can work for longer periods without interruptions, and when it is time to recharge, the batteries are ready to go in no time. Additionally, the drill features an integrated battery level indicator, allowing users to monitor the remaining power at a glance.

Another standout characteristic of the DeWalt 31-260X is its durable construction. Built to withstand the rigors of job site conditions, the drill features a rugged housing that protects internal components from dust and debris. This durability enhances its lifespan, making it a smart investment for those who rely on their tools day in and day out.

To further enhance its versatility, the 31-260X is compatible with a wide range of accessories, including drill bits and driving attachments, catering to various tasks with ease. With a quick-release chuck, users can effortlessly switch between different bits, maximizing productivity on the job.

In summary, the DeWalt 31-260X is a standout cordless drill that combines power, efficiency, and durability. Its impressive motor performance, user-friendly design, and advanced battery technology make it an invaluable tool for anyone looking to complete projects with precision and ease. Whether for professional use or home improvement tasks, the DeWalt 31-260X is a reliable choice that won’t disappoint.