DeWalt 31-260X instruction manual Paso 1 Tensión DE LA Banda DE Distribución

Page 55

PASO 1: TENSIÓN DE LA BANDA DE DISTRIBUCIÓN

1.Si la banda de distribución está demasiado ajustada, se hará difícil mover la mesa. Una banda de distribución suelta puede hacer que la banda saltee un diente en el engranaje de distribución. La desviación en el medio del alcance largo debe ser de 2 a 3 libras.

2.Para ajustar la tensión, ubique uno de los rodillos de la polea de tensión de la banda de distribución debajo del extremo derecho de la unidad, entre los engranajes de distribución. Use una llave de 13 mm (1/2") para aflojar el perno (la tuerca de este perno puede verse en la parte superior de la base).

No gire el volante de elevación mientras la tensión de la banda está relajada.

3.Con la llave de 13 mm (1/2") todavía en el perno de la polea de tensión debajo de la unidad, empuje el huelgo de la banda hacia el extremo de la columna de la unidad y ajuste el perno.

Tenga cuidado de no ajustar la tuerca en exceso. Esto podría aplastar el espaciador que se encuentra en el interior. Una torsión aproximada de 50 libras-pulgada será suficiente. Para estar seguro de que el espaciador no sufrirá daños, tome el rodillo de la polea de tensión. Si se puede mover aproximadamente 3,2 mm (1/8") en forma vertical, el espaciador estará bien.

4.Con la tensión adecuada de la banda, ajuste la mesa.

PASO 2: INSPECCIÓN DE LA PLACA DE SOPORTE DE LA MESA

1.Para comprobar que la placa de soporte de la mesa esté montada sobre una placa plana y paralela al tambor, use una llave hexagonal de 4,8 mm (3/16") (A) Fig. 38 y una llave abierta de 13 mm (1/2") (B) para aflojar los cuatro pernos hexagonales que sujetan la placa de soporte a los pernos de elevación. Coloque un bloque de madera (C) Fig. 39 de aproximadamente 19 mm de ancho x 51 a 76 mm de alto (3/4" x 2" a 3") debajo de la placa de soporte de la mesa en la base de la unidad, junto a uno de los pernos de elevación. Gire el perno de elevación hacia arriba o hacia abajo hasta que la placa de soporte apenas se separe del bloque. REPITA la comprobación de la distancia en cada uno de los otros tres pernos de elevación. Deben estar a 0,4 mm (1/64") del otro (O) Fig. 410.

2.Mientras sostiene la llave hexagonal de 13 mm (1/2") en el perno para evitar que gire, vuelva a ajustar los cuatro pernos hexagonales.

3.Con la llave de 13 mm (1/2") y una llave hexagonal de 4,8 mm (3/16"), afloje el perno de cabeza troncocónica delantero derecho

(B) Fig. 38 cuatro vueltas completas (S) Fig. 40. Gire el perno de nivelación en el sentido de las agujas del reloj hasta que no esté en contacto con la placa de soporte (P) Fig. 40. Luego, gire el mismo perno en sentido contrario a las agujas del reloj hasta que apenas toque la placa de soporte sin levantarla (O) Fig. 41. Sujete el perno de elevación (L) Fig. 41 con la llave de 13 mm (1/2") para evitar que gire. Ajuste el perno de cabeza troncocónica (B) con la llave hexagonal de 4,8 mm (3/16").

4.Con el nivel de la placa de soporte, mueva la mesa hacia arriba y hacia abajo. Si el movimiento aún es limitado, repita este procedimiento.

A

B

Fig. 37

B

P

L

Fig. 39

 

S

 

B

C

 

Fig. 38

 

 

 

 

 

B

 

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

 

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

L

Fig. 40

55

Image 55
Contents 31-260X Important Safety Instructions Table of ContentsSafety Guidelines Definitions Stay ALERT, Watch What YOU are DOING, and USE General Safety RulesGrounding Instructions Additional Specific Safety RulesPower Connections Motor SpecificationsAll grounded, cord-connected machines Minimum Gauge Extension CordFunctional Description Carton ContentsAssembly Tools Required AssemblyAssembly Time Estimate HOW to Attach and Level the Feed Table HOW to Attach the HandwheelOperating Controls and Adjustments To Check and Adjust Tension HOW to Raise the TableHOW to Check and Adjust the Feed Belt Tracking and Tension To Check and Adjust TrackingHOW to SET the Height Scale HOW to Check and Adjust the Table Parallel to the DrumDrum Motor Overload Protection HOW to Remove and Replace the Drum Sanding Belt HOW to Change the Drum Speeds and Replace the Drive BeltFeed Belt Motor Overload Protection HOW to Remove and Replace the Feed BeltFrequently Asked Questions HOW do I Sand Multiple BOARDS? Dust Collection RecommendationWhat Causes Burn MARKS? What are the Maximum and Minimum Sanding Stock SIZES?HOW do I GET STARTED? HOW to Increase Sanding Belt LifeTable Movement Troubleshooting Guide HOW do I Sand Boards Wider than 18?Checking the Table Support Plate Timing Belt TensionChecking the Lock NUT Adjustment Troubleshooting MaintenanceAligning Elevating Bolt Bushings Lubrication & Rust Protection ServiceKeep Machine Clean Replacement PartsService and Repairs AccessoriesWarranty Free Warning Label ReplacementMesures DE Sécurité Définitions LES Instructions Importantes DE SureteLA Proposition DE Californie Lutilisation DE CET Outil Peut Règles DE Sécurité GénéralesInstructions DE Mise À LA Terre Règles Spécifiques Additionnelles DE SûretéRaccordements Électriques Spécifications DU MoteurMesur Minimum DE Corde D’EXTENSION Cordon DE RallongeDésemballage ET Nettoyage Description FonctionnelleContenus DE Boite AVANT-PROPOSAssemblage DU Socle AssemblageOutils Nécessaires Pour L’ASSEMBLEE Lestimation DE Temps DassembleeFixation ET Mise DE Niveau DE LA Table D’ALIMENTATION Fixation DU VolantTAG Comment Commencer ET Arreter LA Machine FonctionnementLoperation Controle DE LE ET LES Ajustements Fixation DE L’INDICATEUR D’ALIMENTATION « SA »Vérification ET Réglage DE L’ALIGNEMENT Élévation DE LA TableVérification ET Réglage DE LA Tension Réglage DE L’ÉCHELLE DE Hauteur Protection Contre LES Surcharges DU Moteur DU TambourRetrait ET Remplacement DE LA Bande Abrasive DU Tambour Retrait ET Remplacement DE LA Courroie D’ALIMENTATION Quels Facteurs Influent SUR LES Opérations DE PONÇAGE? Demande Frequemment AUX QuestionsComment PUIS-JE Poncer LES Planches COLLÉES? Quelles Sont LES Recommandations Pour LE DépoussiérageQU’EST-CE QUI Cause LES Marques DE BRÛLURE? Comment PUIS-JE Poncer Plusieurs PLANCHES?Ajourner LE Guide DE Depannage DE Mouvement PAR OÙ DOIS-JE COMMENCER?Étape 2 Vérification DE LA Plaque DE Fixation DE LA Table Étape 1 Tension DE LA Courroie CrantéeÉtape 3 Vérification DE L’AJUSTEMENT DU CONTRE-ÉCROU Depannage EntretienÉtape 4 Alignement DES Bagues DE Boulon D’ÉLÉVATION Lubrification ET Protection Contre LA Rouille Inspection ET Remplacement DES BrossesGarder LA Machine Propre Démarrage ImpossibleEntretien ET Réparation AccessoiriesRemplacement Gratuit DE Létiquette GarantiePautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesEL USO DE Esta Herramienta Puede Normas Generales DE SeguridadInstrucciones DE Conexión a Tierra Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Especificaciones DEL MotorCordón DE Extensión DE Calibre Mínimo Cordones DE ExtensiónDesempaquetado Y Limpieza Descripción FuncionalContenido DE Carton PrologoHerramientas DE Ensamblaje Requeridas EnsamblajeEstimación DEL Tiempo DE Ensamblaje Cómo Instalar Y Nivelar LA Mesa DE Alimentación Cómo Instalar EL VolanteCómo Conectar EL Indicador DE Alimentación SA OperaciónControles Y Ajustes Operacionales Arrancando Y Deteniendo LA MaquinaPara Comprobar Y Ajustar LA Trayectoria Cómo Elevar LA MesaPara Comprobar Y Ajustar LA Tensión Protección Contra Sobrecarga DEL Motor DEL Tambor Cómo Configurar LA Escala DE AlturaCómo Comprobar Y Ajustar LA Mesa Paralela AL Tambor Cómo Quitar Y Reemplazar LA Banda DE Lijado DEL Tambor Cómo Quitar Y Reemplazar LA Banda DE Alimentación Hizo CON Frecuencia Preguntas ¿CÓMO Lijo LAS Tablas AHUECADAS, Curvadas O TORCIDAS? ¿QUÉ Produce LAS Marcas DE QUEMADURA?¿CÓMO Lijo Varias TABLAS? ¿CÓMO Lijo LOS Bordes DE LAS TABLAS?Posponga LA Guia DE Localizacion DE Fallas DE Movimiento ¿CÓMO Lijo Tablas MÁS Anchas QUE 457 MM 18?Paso 2 Inspección DE LA Placa DE Soporte DE LA Mesa Paso 1 Tensión DE LA Banda DE DistribuciónPaso 3 Comprobación DEL Ajuste DE LA Tuerca DE Seguridad Localizacion DE Fallas MaintenanceServicio MantenimientoAccessories Identificación Delproducto Póliza DE GarantíaExcepciones Your ACHIEVEMENT. OUR Tools

31-260X specifications

The DeWalt 31-260X is a powerful and versatile cordless drill that stands out in the competitive world of power tools. With its combination of robust performance, advanced features, and user-friendly design, it has become a favorite among both professionals and DIY enthusiasts alike.

One of the main features of the DeWalt 31-260X is its high-performance motor, which delivers impressive torque and speed to tackle a variety of materials and applications. The drill operates at multiple speed settings, allowing users to adjust the RPM according to their specific project needs. This feature is particularly useful when working with different materials, such as wood, metal, or plastic, ensuring optimal results with minimal effort.

The 31-260X also boasts a compact and lightweight design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. The ergonomic grip is designed for comfort and control, providing a secure hold that enhances precision during drilling and driving tasks.

In terms of battery technology, the DeWalt 31-260X is equipped with the brand's state-of-the-art lithium-ion batteries, which deliver extended run times and shorter charge times. This ensures that users can work for longer periods without interruptions, and when it is time to recharge, the batteries are ready to go in no time. Additionally, the drill features an integrated battery level indicator, allowing users to monitor the remaining power at a glance.

Another standout characteristic of the DeWalt 31-260X is its durable construction. Built to withstand the rigors of job site conditions, the drill features a rugged housing that protects internal components from dust and debris. This durability enhances its lifespan, making it a smart investment for those who rely on their tools day in and day out.

To further enhance its versatility, the 31-260X is compatible with a wide range of accessories, including drill bits and driving attachments, catering to various tasks with ease. With a quick-release chuck, users can effortlessly switch between different bits, maximizing productivity on the job.

In summary, the DeWalt 31-260X is a standout cordless drill that combines power, efficiency, and durability. Its impressive motor performance, user-friendly design, and advanced battery technology make it an invaluable tool for anyone looking to complete projects with precision and ease. Whether for professional use or home improvement tasks, the DeWalt 31-260X is a reliable choice that won’t disappoint.