DeWalt 31-260X instruction manual Cómo Quitar Y Reemplazar LA Banda DE Lijado DEL Tambor

Page 50

CÓMO CAMBIAR LAS VELOCIDADES DEL TAMBOR Y REEMPLAZAR LA BANDA IMPULSORA

La lijadora de tambor tiene dos velocidades del tambor: 674 ó 1.006 metros de superficie (2.210 ó 3.300 pies de superficie) por minuto.

Para cambiar las velocidades del tambor o para reemplazar la banda impulsora:

Desconecte la máquina de la fuente de energía.

1.Levante la cubierta superior del tambor (A) Fig. 25.

2.Retire los dos tapones para orificio (B) Fig. 25.

3.Coloque un manguito de 14 mm (9/16") con una extensión (no suministrada) en uno de los dos orificios en los que se quitaron los tapones para orificio.

NOTA: Si no tiene una extensión de manguito, retire los pernos (G) Fig. 25 del panel para llegar a los pernos. Afloje un perno hexagonal y luego el otro para aliviar la tensión del motor. Levante un poco el motor (ubicado debajo de la máquina) para aliviar la tensión en la banda. Reemplace o cambie las posiciones de la banda en las poleas.

IMPORTANTE: La velocidad del tambor de lijado es de 1.006 metros de superficie (3.300 pies de superficie) por minuto con la banda en las poleas internas (A) Fig. 27. IMPORTANTE: La velocidad del tambor de lijado es de 674 metros de superficie (2.210 pies de superficie) por minuto con la banda en las poleas internas (A) Fig. 26.

NOTA: Coloque correctamente la banda impulsora Poly-V en las poleas para proporcionar el máximo rendimiento con el mínimo desgaste de banda.

4.Luego de haber reemplazado o vuelto a colocar la banda en las poleas, aplique una presión hacia abajo en el motor y ajuste los dos pernos de cabeza hexagonal que se aflojaron en el PASO 3.

5.Con el dedo, presione levemente en mitad de la banda entre las poleas para comprobar que la tensión sea adecuada. Una desviación de aproximadamente 4,8 mm (3/16") es correcta.

6.Vuelva a colocar los tapones para orificio (B) Fig. 25.

CÓMO QUITAR Y REEMPLAZAR LA BANDA DE LIJADO DEL TAMBOR

 

A

 

B

G

G

 

 

Fig. 25

Fig. 26

A

A

Fig. 27

B

A

C

Fig. 28

A

C

Fig. 29

B

D

A

Fig. 30

B

Una pinza de resorte a cada lado del tambor sujeta la banda de lijado en posición.

Desconecte la máquina de la fuente de energía.

Una pinza de resorte a cada lado del tambor sujeta la banda de lijado en posición.

1.Abra la cubierta del tambor.

2.Presione las pinzas de resorte (B) Fig. 28 juntas y retire un extremo de la banda de lijado (A).

NOTA: La pinza debe estar completamente oprimida contra el soporte del tambor.

3.Gire el tambor (C) Fig. 29 a mano hasta que llegue a la otra pinza de resorte. Presione esa pinza de resorte para abrirla y quite la banda de lijado.

4.Para reemplazar la banda de lijado, presione las pinzas de resorte (B) Fig. 29 juntas e introduzca un extremo de la banda de lijado (A) a través de la ranura en el tambor y dentro de la pinza de resorte. Alinee el extremo cónico de la banda de lijado con el borde del tambor.

5.Enrolle la banda de lijado (A) Fig. 30 con firmeza alrededor del cilindro del tambor (D), manteniendo cada envoltura cerca del borde anterior.

IMPORTANTE: No superponga los bordews de la banda de lijado.(A).

6.Introduzca el otro extremo de la banda de lijado en la pinza de resorte izquierda y ajústelo tan fuerte como sea posible.

La banda de lijado se estirará durante el uso. De manera periódica, presione la pinza de resorte y ajuste la banda en la pinza.

50

Image 50
Contents 31-260X Safety Guidelines Definitions Table of ContentsImportant Safety Instructions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEMotor Specifications Additional Specific Safety RulesPower Connections Grounding InstructionsMinimum Gauge Extension Cord All grounded, cord-connected machinesCarton Contents Functional DescriptionAssembly Time Estimate AssemblyAssembly Tools Required HOW to Attach the Handwheel HOW to Attach and Level the Feed TableOperating Controls and Adjustments To Check and Adjust Tracking HOW to Raise the TableHOW to Check and Adjust the Feed Belt Tracking and Tension To Check and Adjust TensionDrum Motor Overload Protection HOW to Check and Adjust the Table Parallel to the DrumHOW to SET the Height Scale HOW to Change the Drum Speeds and Replace the Drive Belt HOW to Remove and Replace the Drum Sanding BeltHOW to Remove and Replace the Feed Belt Feed Belt Motor Overload ProtectionFrequently Asked Questions What are the Maximum and Minimum Sanding Stock SIZES? Dust Collection RecommendationWhat Causes Burn MARKS? HOW do I Sand Multiple BOARDS?HOW do I Sand Boards Wider than 18? HOW to Increase Sanding Belt LifeTable Movement Troubleshooting Guide HOW do I GET STARTED?Timing Belt Tension Checking the Table Support PlateAligning Elevating Bolt Bushings Troubleshooting MaintenanceChecking the Lock NUT Adjustment Replacement Parts ServiceKeep Machine Clean Lubrication & Rust ProtectionFree Warning Label Replacement AccessoriesWarranty Service and RepairsLA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Règles DE Sécurité Générales Lutilisation DE CET Outil PeutSpécifications DU Moteur Règles Spécifiques Additionnelles DE SûretéRaccordements Électriques Instructions DE Mise À LA TerreCordon DE Rallonge Mesur Minimum DE Corde D’EXTENSIONAVANT-PROPOS Description FonctionnelleContenus DE Boite Désemballage ET NettoyageLestimation DE Temps Dassemblee AssemblageOutils Nécessaires Pour L’ASSEMBLEE Assemblage DU SocleTAG Fixation DU VolantFixation ET Mise DE Niveau DE LA Table D’ALIMENTATION Fixation DE L’INDICATEUR D’ALIMENTATION « SA » FonctionnementLoperation Controle DE LE ET LES Ajustements Comment Commencer ET Arreter LA MachineVérification ET Réglage DE LA Tension Élévation DE LA TableVérification ET Réglage DE L’ALIGNEMENT Protection Contre LES Surcharges DU Moteur DU Tambour Réglage DE L’ÉCHELLE DE HauteurRetrait ET Remplacement DE LA Bande Abrasive DU Tambour Retrait ET Remplacement DE LA Courroie D’ALIMENTATION Demande Frequemment AUX Questions Quels Facteurs Influent SUR LES Opérations DE PONÇAGE?Comment PUIS-JE Poncer Plusieurs PLANCHES? Quelles Sont LES Recommandations Pour LE DépoussiérageQU’EST-CE QUI Cause LES Marques DE BRÛLURE? Comment PUIS-JE Poncer LES Planches COLLÉES?PAR OÙ DOIS-JE COMMENCER? Ajourner LE Guide DE Depannage DE MouvementÉtape 1 Tension DE LA Courroie Crantée Étape 2 Vérification DE LA Plaque DE Fixation DE LA TableÉtape 4 Alignement DES Bagues DE Boulon D’ÉLÉVATION Depannage EntretienÉtape 3 Vérification DE L’AJUSTEMENT DU CONTRE-ÉCROU Démarrage Impossible Inspection ET Remplacement DES BrossesGarder LA Machine Propre Lubrification ET Protection Contre LA RouilleGarantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationInstrucciones DE Seguridad Importantes Pautas DE SEGURIDAD/DEFINICIONESNormas Generales DE Seguridad EL USO DE Esta Herramienta PuedeEspecificaciones DEL Motor Normas Específicas Adicionales DE SeguridadConexiones a LA Fuente DE Alimentación Instrucciones DE Conexión a TierraCordones DE Extensión Cordón DE Extensión DE Calibre MínimoPrologo Descripción FuncionalContenido DE Carton Desempaquetado Y LimpiezaEstimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Cómo Instalar EL Volante Cómo Instalar Y Nivelar LA Mesa DE AlimentaciónArrancando Y Deteniendo LA Maquina OperaciónControles Y Ajustes Operacionales Cómo Conectar EL Indicador DE Alimentación SAPara Comprobar Y Ajustar LA Tensión Cómo Elevar LA MesaPara Comprobar Y Ajustar LA Trayectoria Cómo Comprobar Y Ajustar LA Mesa Paralela AL Tambor Cómo Configurar LA Escala DE AlturaProtección Contra Sobrecarga DEL Motor DEL Tambor Cómo Quitar Y Reemplazar LA Banda DE Lijado DEL Tambor Cómo Quitar Y Reemplazar LA Banda DE Alimentación Hizo CON Frecuencia Preguntas ¿CÓMO Lijo LOS Bordes DE LAS TABLAS? ¿QUÉ Produce LAS Marcas DE QUEMADURA?¿CÓMO Lijo Varias TABLAS? ¿CÓMO Lijo LAS Tablas AHUECADAS, Curvadas O TORCIDAS?¿CÓMO Lijo Tablas MÁS Anchas QUE 457 MM 18? Posponga LA Guia DE Localizacion DE Fallas DE MovimientoPaso 1 Tensión DE LA Banda DE Distribución Paso 2 Inspección DE LA Placa DE Soporte DE LA MesaLocalizacion DE Fallas Maintenance Paso 3 Comprobación DEL Ajuste DE LA Tuerca DE SeguridadMantenimiento ServicioAccessories Excepciones Póliza DE GarantíaIdentificación Delproducto Your ACHIEVEMENT. OUR Tools

31-260X specifications

The DeWalt 31-260X is a powerful and versatile cordless drill that stands out in the competitive world of power tools. With its combination of robust performance, advanced features, and user-friendly design, it has become a favorite among both professionals and DIY enthusiasts alike.

One of the main features of the DeWalt 31-260X is its high-performance motor, which delivers impressive torque and speed to tackle a variety of materials and applications. The drill operates at multiple speed settings, allowing users to adjust the RPM according to their specific project needs. This feature is particularly useful when working with different materials, such as wood, metal, or plastic, ensuring optimal results with minimal effort.

The 31-260X also boasts a compact and lightweight design, making it easy to maneuver in tight spaces and reducing user fatigue during extended use. The ergonomic grip is designed for comfort and control, providing a secure hold that enhances precision during drilling and driving tasks.

In terms of battery technology, the DeWalt 31-260X is equipped with the brand's state-of-the-art lithium-ion batteries, which deliver extended run times and shorter charge times. This ensures that users can work for longer periods without interruptions, and when it is time to recharge, the batteries are ready to go in no time. Additionally, the drill features an integrated battery level indicator, allowing users to monitor the remaining power at a glance.

Another standout characteristic of the DeWalt 31-260X is its durable construction. Built to withstand the rigors of job site conditions, the drill features a rugged housing that protects internal components from dust and debris. This durability enhances its lifespan, making it a smart investment for those who rely on their tools day in and day out.

To further enhance its versatility, the 31-260X is compatible with a wide range of accessories, including drill bits and driving attachments, catering to various tasks with ease. With a quick-release chuck, users can effortlessly switch between different bits, maximizing productivity on the job.

In summary, the DeWalt 31-260X is a standout cordless drill that combines power, efficiency, and durability. Its impressive motor performance, user-friendly design, and advanced battery technology make it an invaluable tool for anyone looking to complete projects with precision and ease. Whether for professional use or home improvement tasks, the DeWalt 31-260X is a reliable choice that won’t disappoint.