Schumacher MODELS SC-600A, SC-1000A owner manual General Charging Notes

Page 15

1.With the charger unplugged from the AC outlet, connect the charger to the battery following the instructions given in Sections 6 and 7.

2.Plug the charger AC power cord into the AC outlet.

3.If necessary, press the BATTERY TYPE button until the correct type is indicated.

4.Read the voltage on the digital display or press the display mode button to set the tester to BATTERY % to read the voltage as a percent of charge.

Tester and Charger: When first turned on, the unit operates only as a tester, not as a charger. To continue to use it only as a tester, avoid pressing the CHARGE RATE button. Selecting a charge rate activates the battery charger and deactivates the tester.

Power-Up Idle Time Limit: If no button is pressed within 15 minutes after the battery charger is first powered up, the charger will automatically switch from tester to charger, if a battery is connected. In that case, the battery will be set for the 2A charge rate and 12V REGULAR battery type.

Tester without Time Limit: If either the DISPLAY MODE or BATTERY TYPE button is pressed within the first 10 minutes after the battery charger is powered up, the unit will remain a tester (not a charger) indefinitely, unless a charge rate is selected.

Testing After Charging: After the unit has been changed from tester to charger (by selecting a charge rate), it remains a charger. To change the battery charger back to a tester, press the CHARGE RATE switch until all charge rate LED’s are off.

Tester Status LED’s: When the unit is operating as a battery tester, the status LED’s light under the following conditions:

•The CHARGED (green) LED will light if a charged battery is tested.

•The CHARGING (yellow) LED does not light in the battery test mode.

•The CONNECTED (red) LED lights when a properly connected battery is detected.

•When the tester display mode is set to VOLTAGE, the CHARGED and CHARGING LED’s won’t light.

11.10GENERAL CHARGING NOTES:

Restart: If the charge mode is changed after charging has started (by pressing the CHARGE RATE or BATTERY TYPE button), the charging process will restart.

Voltage: The voltage displayed during charging is the charging voltage and is usually higher than the battery’s resting voltage.

11.11Charging Tips: Read this entire manual before using your battery charger. The following tips serve only as a guide for specific situations:

•12 •

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models SC-600A, SC-1000A, SC-1200A, SSC-1000A, SSC-1500A Page Table of Contents Important Safety Instructions Page DC Connection Precautions Preparing to ChargeCharger Location Page Battery charging ac connections Control panel SC-1000A SC-1200A SSC-1000A Charge Rate Button Display Mode ButtonBattery Type Button Digital DisplayCharging Page Aborted Charge General Charging Notes Calculating charge time Battery SIZE/RATING Charge RATE/CHARGING Time Storage instructions Maintenance instructionsTroubleshooting Problem Possible Cause SolutionProblem Possible Cause Solution Before Returning for Repairs Limited warranty Page Manual DEL usuario Page Página SecciónAdvertencia Riesgo DE Gases Explosivos Instrucciones DE Seguridad ImportantesPrecauciones Personales PREPARación de la carga Ubicación DEL CargadorPrecauciones DE LA Conexión CC Siga Estos Pasos cuando la batería esté afuera del vehículo Carga de bateria Conexiones AC Controles DEL Speedcharge SC-1000A SC-1200A SSC-1000A Abotón DE Charge Rate Botón DE Battery TypePorcentaje y tiempo de carga de la batería La batería SC Instrucciones Para EnsambleInstrucciones DE Operación Descripción generalPage Page Recomendada Calculando EL Tiempo DE CargaMedida DE LA Bateria Nivel DE Carga Solución DE Problemas Posible Causa Instrucciones DE MantenimientoAlmacenaje Problema Posible Causa Solución Antes DE Devolver EL Cargador Para Reparación Garantía Limitada
Top Page Image Contents