Ingersoll-Rand GRG15A06G7, GRS15A06S7, GRS15A04S9, GRG15M06G7, GRG15A06G9 manual Especificaciones

Page 12

PARA PONER LA HERRAMIENTA EN SERVICIO

ESPECIFICACIONES

Modelo	Velocidad	Muela Tipo 27 y 28		Eje y
	Constante			Cubremuela

	rpm	pulgadas	mm

GRG15A–06G–7	6.000	7	178	5/8–11, 7”
GRG15A–06G–9	6.000	9	227	5/8–11, 9”
GRG15A–08G–7	7.500	7	178	5/8–11, 7”
GRG15M–06G–7	6.000	7	178	5/8–11, 7”
GRG15M–06G–9	6.000	9	227	5/8–11, 9”
GRG15M–08G–7	7.500	7	178	5/8–11, 7”

Modelo	Velocidad	Placa de Reserva		Eje
	Constante

	rpm	pulgadas	mm

GRP15A–02P–7	2.500	7	178	5/8–11, 7”
GRS15A–06S–7	6.000	7	178	5/8–11, 7”
GRS15A–04S–9	4.500	9	228	5/8–11, 9”

Image 12

Contents Using the Tool OPERATOR’S ManualGrinder Specific Warnings Placing Tool in Service SANDER/POLISHER Specific WarningsLubrication Model Type 27 and 28 Wheel Spindle and GuardModel Free Speed, rpm Back up Pad Spindle Manuel DE L’OPERATEUR Utilisation DE L’OUTILSignification DES Étiquettes D’AVERTISSEMENT Avertissements Spécifiques AUX MeuleusesMise EN Service DE L’OUTIL Avertissements Particuliers AUX PONCEUSES/POLISSEUSESLubrification SPÉ Cifications Modèle Vitesse à vide Plateau-support Broche Tr/mn PoucesPara Poner LA Herramienta EN SERVI- CIO Utilizació N DE LA HerramientaEtiquetas DE Aviso Avisos Específicos Sobre LAS AmoladorasAvisos Especificos DE LIJADORA/PULIDORA Para Poner LA Herramienta EN ServicioLubricació N Irax N P Irax N 1LBEspecificaciones Modelo Velocidad Placa de Reserva Eje Constante Rpm PulgadasColocando a Ferramenta EM Funcionamento Usando a FerramentaIdentificaçã O do RÓ Tulo DE Advertê Ncia Advertê Ncias Específicas Sobre a EsmeriladoraAdvertê Ncia Colocando a Ferramenta EM Funcionamento Lubrificaçã OEspecificaçõ ES Modelo Velocidade Livre Almofada Veio Rpm PolSection Maintenance Section Part Number for OrderingMaintenance Section 77H-KVLT Disassembly of the Angle Head General InstructionsFor GRG15A or GRG15M Models Disassembly of the Throttle Lever and Inlet Disassembly of the Motor and ThrottleFor GRP15A or GRS15A Models Disassembly of the Bevel Pinion Driver For GRP15A-02P-7 ModelsFor GRG15A, GRG15M or GRS15A Models Assembly of the Motor and Throttle Assembly of the Bevel Pinion DriverFor GRP15A Models Assembly of the Throttle Lever and Inlet Locking Lever AssemblyAssembly of the Angle Head For Type 27 Mounted WheelsFor Type 28 Mounted Wheels For GRP15A, GRS15A ModelsProbable Cause Solution Never operate a Grinder without an InletBushing Screen. Ingestion of dirt into Grinder can, in some cases, cause an unsafeTrouble Probable Cause Solution Rear End Plate Assembly is a matched set. SeeDisassembly and assembly instructions Do not exceed 52.5 ft-lb 71.5 Nm torque

PARA PONER LA HERRAMIENTA EN SERVICIO

ESPECIFICACIONES

Modelo

Velocidad

Placa de Reserva

Eje

Constante

rpm

pulgadas