Ingersoll-Rand GRG15A08G7 manual Especificaçõ ES, Modelo Velocidade Livre Almofada Veio Rpm Pol

Page 16

COLOCANDO A FERRAMENTA EM FUNCIONAMENTO

ESPECIFICAÇÕ ES

Modelo	Velocidade Livre	Disco Tipo 27 e 28		Veio e
				Resguardo

	rpm	pol.	mm

GRG15A–06G–7	6.000	7	178	5/8–11, 7”
GRG15A–06G–9	6.000	9	227	5/8–11, 9”
GRG15A–08G–7	7.500	7	178	5/8–11, 7”
GRG15M–06G–7	6.000	7	178	5/8–11, 7”
GRG15M–06G–9	6.000	9	227	5/8–11, 9”
GRG15M–08G–7	7.500	7	178	5/8–11, 7”

Modelo	Velocidade Livre	Almofada		Veio

	rpm	pol.	mm

GRP15A–02P–7	2.500	7	178	5/8–11, 7”
GRS15A–06S–7	6.000	7	178	5/8–11, 7”
GRS15A–04S–9	4.500	9	228	5/8–11, 9”

Image 16

Contents Using the Tool OPERATOR’S ManualGrinder Specific Warnings SANDER/POLISHER Specific Warnings Placing Tool in ServiceLubrication Type 27 and 28 Wheel Spindle and Guard ModelModel Free Speed, rpm Back up Pad Spindle Manuel DE L’OPERATEUR Utilisation DE L’OUTILSignification DES Étiquettes D’AVERTISSEMENT Avertissements Spécifiques AUX MeuleusesAvertissements Particuliers AUX PONCEUSES/POLISSEUSES Mise EN Service DE L’OUTILLubrification SPÉ Cifications Modèle Vitesse à vide Plateau-support Broche Tr/mn PoucesPara Poner LA Herramienta EN SERVI- CIO Utilizació N DE LA HerramientaEtiquetas DE Aviso Avisos Específicos Sobre LAS AmoladorasAvisos Especificos DE LIJADORA/PULIDORA Para Poner LA Herramienta EN ServicioLubricació N Irax N P Irax N 1LBEspecificaciones Modelo Velocidad Placa de Reserva Eje Constante Rpm Pulgadas Colocando a Ferramenta EM Funcionamento Usando a FerramentaAdvertê Ncias Específicas Sobre a Esmeriladora Identificaçã O do RÓ Tulo DE Advertê NciaAdvertê Ncia Colocando a Ferramenta EM Funcionamento Lubrificaçã OEspecificaçõ ES Modelo Velocidade Livre Almofada Veio Rpm PolSection Maintenance Section Part Number for OrderingMaintenance Section 77H-KVLT General Instructions Disassembly of the Angle HeadFor GRG15A or GRG15M Models Disassembly of the Motor and Throttle Disassembly of the Throttle Lever and InletFor GRP15A or GRS15A Models For GRP15A-02P-7 Models Disassembly of the Bevel Pinion DriverFor GRG15A, GRG15M or GRS15A Models Assembly of the Bevel Pinion Driver Assembly of the Motor and ThrottleFor GRP15A Models Assembly of the Throttle Lever and Inlet Locking Lever AssemblyAssembly of the Angle Head For Type 27 Mounted WheelsFor Type 28 Mounted Wheels For GRP15A, GRS15A ModelsProbable Cause Solution Never operate a Grinder without an InletBushing Screen. Ingestion of dirt into Grinder can, in some cases, cause an unsafeTrouble Probable Cause Solution Rear End Plate Assembly is a matched set. SeeDisassembly and assembly instructions Do not exceed 52.5 ft-lb 71.5 Nm torque

COLOCANDO A FERRAMENTA EM FUNCIONAMENTO

ESPECIFICAÇÕ ES

Modelo

Velocidade Livre

Almofada

Veio

rpm

pol.