Chicago Electric 96698 Maintenance Servicing, Cleaning, Maintenance, Lubrication

Page 15

Maintenance And

Servicing

Procedures not specifically explained in this manual must be performed only by a qualified technician.

WARNING To prevent serious injury

from accidental operation:

Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.

To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.

Cleaning, Maintenance, and

Lubrication

1.BEFORE EACH USE, inspect the general condition of the tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation.

2.After Use, clean external surfaces of the tool with clean, moist cloth.

To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach.

3.If the blade has become dirty, use a blade cleaner (not included) to clean it. Dirty blades will bind more easily, and will more often overheat and burn the wood as it cuts. Overheated blades dull more easily.

4.If the Blade has become dull, replace it. Dull blades will cause increased tear- out and ragged edges on the cuts.

5.Occasionally clean the Slides, rotating Table components and other moving parts. Use a good quality dry lubricant (not included) which will not attract dust.

Cover

Laser Battery Housing

Laser Switch

6.To replace the laser Batteries: Lift the cover off the laser housing. Replace the batteries with two ‘AAA’ batteries and close the cover. CAUTION! To prevent injury, position batteries in proper polarity and do not install batteries of different types, charge levels, or capacities together.

7.WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.

SKU 96698

For technical questions, please call 1-800-444-3353.

Page 15

Image 15
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callFor technical questions, please call General Safety RulesWork area safety Save This ManualPersonal safety Electrical safety Respirator when using thisDo not expose power tools to rain Unplugging the power tool. KeepService Specific Safety RulesFor technical questions, please call Grounding Prong PlugsDouble Insulated Tools Tools With Two Prong Plugs See Table a SymbologyExtension Cords 25’ 50’ 75’Important Components of the Miter Saw For technical questions, please call Assembly SpecificationsInitial Set Up Instructions List of contentsGeneral Operating Instructions Work Piece and Work Area Set UpOperating Instructions Mounting the SawUsing the Work Piece Extension Supports Making a Cut Adjusting the Miter AngleAdjusting the Bevel Angle Using the Depth StopFor technical questions, please call Cleaning, Maintenance, Lubrication Maintenance ServicingReplacing the Blade Adjusting the Miter Table Indicator Adjusting the FenceAdjusting or Replacing the Kerf Board Cleaning and Lubricating Miter SawProblem Possible Causes Likely Solutions TroubleshootingPart Description Qty Parts ListParts List Assembly Diagram Enlarged, Left Side Assembly Diagram Enlarged, Right Side Record Product’s Serial Number Here Limited 90 DAY WarrantyScier de Biseautage Double Glissant Situation non reliée Regles de Securite GeneralsUtilisez un outil électrique. Ne De choc électriqueSécurité Personnelle Soyez vigilant, surveillez ceRotative de l’outil peut causer des blessures Regles de Securite Specifiques Conservez CES Instructions Prise de courant de 3 dents et Prise de courant murale Fiche à Deux BrochesSymboles Longueur de laRallonge ’Image Composants Importants de La Scie à OngletBouton de Fixer Les Extensions de Support ContenuAssemblage Description QtéMontage de La Scie Monter de Piece à Travailler et Espace de TravailAttacher Le Sac à Poussière Instructions de Fonctionnement Generals Utiliser Les Extension de Support De Pièces Réglage d’Angle d’OngletRégler L’Angle de Coupe en Biseau Effectuer Une Coupe Utiliser Le Butée FixeModèle Avertissement Avertissement Pour Reduire Remplacez La LameRégler La Garde de Guidage Transporter La Scie à Onglet Ajuster or Remplacer Le Plateau De DécoupeDépannage Problème Cause SolutionDépannage Pièce Description Qté Liste de pièces109 Orifice à Sciure 110 Ensemble du Boîtier de la lame Diagramme DE MONTAGE, Côté Gauche Diagramme DE MONTAGE, Côté Droite Garantie Déférez au texte anglais pour l’explication de garantieEnregistrez le Numéro de série de Produit Ici