Chicago Electric 96698 Troubleshooting, Problem Possible Causes Likely Solutions

Page 19

Troubleshooting

Problem

 

Possible Causes

 

Likely Solutions

Tool will not

1.

No power at outlet.

1.

Check power at outlet.

start

2.

Cord not connected.

2.

Check that cord is plugged in.

Tool operates

1.

Low power supply or improper

1.

Check power supply and power cords.

sporadically or

 

extension cords.

 

 

at low power

2.

Worn or cracked Carbon Brushes.

2.

Check Carbon Brushes. Replace if damaged

 

 

 

 

or worn.

Wood burns at

1.

Dirty Blade.

1.

Clean Blade using blade cleaner or mineral

ends when cut

 

 

 

spirits.

 

2.

Material is binding.

2.

Check position of work material on Table.

 

 

 

 

Material must be flat, flush against Fence

 

 

 

 

and supported on ends.

Material frays

1.

Finished side is down

1.

Always have finished side of material up or

or chips out.

 

 

 

facing you. Bottom and back side are prone

 

 

 

 

to chip out.

 

2.

Blade is chipped or dull.

2.

Check for damaged teeth. Sharpen or

 

 

 

 

replace blade.

 

3.

Blade is inappropriate for

3.

Check blade manufacturer’s

 

 

material.

 

recommendations for material being cut. For

 

 

 

 

cross cutting hard wood and for precision

 

 

 

 

cuts use a thin kerf blade with 60 or more

 

 

 

 

teeth.

 

4.

Material is unsupported.

4.

Use a thin piece of sacrificial material, such

 

 

 

 

as 1/4” plywood, underneath or behind the

 

 

 

 

material to support the edges of the material

 

 

 

 

as it is being cut.

Blade binds

1.

Material is misaligned on the saw

1.

Material must be flat on table, flush against

slowing or

 

or ends are not supported.

 

the fence and supported on both ends.

stopping saw.

2.

Material is wet, contaminated or

2.

Check condition of material and check

 

 

inappropriate blade is being used.

 

compatibility of blade to material.

Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/ or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto.

SKU 96698

For technical questions, please call 1-800-444-3353.

Page 19

Image 19
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callFor technical questions, please call General Safety RulesWork area safety Save This ManualPersonal safety Electrical safety Respirator when using thisDo not expose power tools to rain Unplugging the power tool. KeepService Specific Safety RulesFor technical questions, please call Prong Plugs GroundingDouble Insulated Tools Tools With Two Prong Plugs See Table a SymbologyExtension Cords 25’ 50’ 75’Important Components of the Miter Saw For technical questions, please call Assembly SpecificationsInitial Set Up Instructions List of contentsGeneral Operating Instructions Work Piece and Work Area Set UpOperating Instructions Mounting the SawUsing the Work Piece Extension Supports Making a Cut Adjusting the Miter AngleAdjusting the Bevel Angle Using the Depth StopFor technical questions, please call Cleaning, Maintenance, Lubrication Maintenance ServicingReplacing the Blade Adjusting the Miter Table Indicator Adjusting the FenceAdjusting or Replacing the Kerf Board Cleaning and Lubricating Miter SawProblem Possible Causes Likely Solutions TroubleshootingPart Description Qty Parts ListParts List Assembly Diagram Enlarged, Left Side Assembly Diagram Enlarged, Right Side Record Product’s Serial Number Here Limited 90 DAY WarrantyScier de Biseautage Double Glissant Situation non reliée Regles de Securite GeneralsUtilisez un outil électrique. Ne De choc électriqueSécurité Personnelle Soyez vigilant, surveillez ceRotative de l’outil peut causer des blessures Regles de Securite Specifiques Conservez CES Instructions Prise de courant de 3 dents et Prise de courant murale Fiche à Deux BrochesLongueur de la SymbolesRallonge ’Image Composants Importants de La Scie à OngletBouton de Fixer Les Extensions de Support ContenuAssemblage Description QtéMonter de Piece à Travailler et Espace de Travail Montage de La ScieAttacher Le Sac à Poussière Instructions de Fonctionnement Generals Réglage d’Angle d’Onglet Utiliser Les Extension de Support De PiècesRégler L’Angle de Coupe en Biseau Effectuer Une Coupe Utiliser Le Butée FixeModèle Avertissement Avertissement Pour Reduire Remplacez La LameRégler La Garde de Guidage Transporter La Scie à Onglet Ajuster or Remplacer Le Plateau De DécoupeDépannage Problème Cause SolutionDépannage Pièce Description Qté Liste de pièces109 Orifice à Sciure 110 Ensemble du Boîtier de la lame Diagramme DE MONTAGE, Côté Gauche Diagramme DE MONTAGE, Côté Droite Déférez au texte anglais pour l’explication de garantie GarantieEnregistrez le Numéro de série de Produit Ici