DeWalt DWS535 Foot Plate Adjustment for 90˚ Cuts, Kerf Indicator Fig, Operation, Changing Blades

Page 10

English

which consists of a calibrated angle quadrant (I) and a bevel adjustment lever (H).The angle quadrant allows for coarse adjustment

(N) or fine adjustment (O) to achieve better accuracy in cutting.

To set the saw for a bevel cut

1.Lift the bevel adjustment lever (H) and tilt foot plate to the desired angle by aligning the pointer with the desired angle mark.

2.Push the bevel adjustment lever down and tighten securely to lock the angle.

Foot Plate Adjustment for 90˚ Cuts

If additional adjustment is needed

1. Adjust the saw to 0˚ bevel.

fig. 7

2. Retract blade guard. Place the saw on blade side.

3. Lift bevel adjustment lever. Place a square against the blade and foot plate to adjust the 90˚ setting.

4.Move the adjustment screw, located on the bottom of the foot plate (Fig. 7), so that the foot plate will stop at the proper angle.

5.Confirm the accuracy of the setting by checking the squareness of an actual cut on a scrap piece of material.

Kerf Indicator (Fig. 8)

The front of the saw foot plate (D) has a 0˚ kerf indicator (F) and a 45˚ kerf indicator (G) for vertical and bevel cutting. The kerf indicators enable you to guide the saw along the cutting lines penciled on the workpiece.

The indicator aligns with the left (outer) side of the saw blade. The moving blade making the slot or “kerf” cut falls to the right of the indicator. Position the saw along the penciled cutting line so that the kerf falls into the waste or surplus material. Marking indicators on the front of the foot plate are at 1/2" (13 mm) intervals for additional cutting guides.

Fig. 8

p

g

 

f

D

 

Kerf indicators (P) are also located on the inside of the foot plate to keep the saw square when cutting.

Operation

Warning: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

Important: Always make sure the depth adjustment locking lever is in the down position before operating saw.

Trigger Switch (Fig. 1)

Warning: To reduce the risk of serious personal injury, hold saw with both hands when starting the saw to avoid kickback.

Press the trigger switch (A) to turn the tool on. Release the trigger switch to turn the tool off.

NOTE: This tool has no provision to lock the trigger in the on position and should never be locked on by any other means.

Changing Blades (Fig. 1, 9–12)

IMPortant: Most replacement blades come with a round arbor center opening which must be knocked out so a diamond-shaped

8

Image 10
Contents Guide Dutilisation Manual de instrucciones DWS535, DWS535T 4 184 mm Worm Drive SawElectrical safety Definitions Safety GuidelinesWork area safety InjuryPersonal safety Power tool use and careService Safety Instructions for All SawsCauses and Operator Prevention of Kickback Additional Safety Instructions Lower Guard Safety InstructionsAWG Saw Hook Fig Components FigIntended USE Cutting Depth Adjustment , 4 Twist-lock Connector DWS535TBevel Angle Adjustment Trigger Switch Fig Foot Plate Adjustment for 90˚ CutsKerf Indicator Fig OperationTo Install the Blade , 10 To remove knockoutTo Replace the blade Fig Blade BladesKickback Teeth ApplicationWorkpiece Support Fig Cutting Pocket Cutting Fig Ripping FigMaintenance Cleaning Lubrication To check oilYear free service Three Year Limited WarrantyAccessories DAY money back GuaranteeEnglish Scies Circulaires à Vis Sans Fin DWS535 et DWS535T, 184 mm 7-1/4 poRisques de dommages matériels Définitions lignes directrices en matière de sécuritéGraves Entraîner des blessures légères ou modérées Sécurité du lieu de travailSécurité personnelle Utilisation et entretien d’un outil électrique Consignes de sécurité propres à toutes les sciesRéparation Français Consignes additionnelles de sécurité Consignes de sécurité relatives au protège-lame inférieurPlus 120V240V AWGUtilisation Ultérieure Description Fig Usage PrévuRéglage de profondeur de coupe , 4 Crochet de suspension FigConnecteur à verrouillage par rotation DWS535T Avertissement pour réduireIndicateur de trait de scie Fig Réglage de l’angle de chanfreinRéglage de la plaque d’assise pour des coupes à 90˚ Réglage DE LA Scie Pour Effectuer UNE coupe en biseauGâchette Fig Changement de lameRetrait DE l’ALÉSAGE amovible Installation DE LA Lame , 10 Pour changer LA Lame Fig Desserrer vers la gauche vers la droiteCarter DE Lame Inférieur LamesRebonds LameTorsion DE LA Lame Mésalignement DE Coupe Configuration DE Profondeur DE Coupe IncorrecteSupport DE Pièce Inadéquat Matériaux Nécessitant UNE Attention SpécialeCoupe Support de pièce FigAvertissement il est important de sou Coupe longitudinale FIG Nettoyage EntretienCoupe interne fig Balais Fig LubrificationVérification DE l’huile Réparations AccessoiresService D’ENTRETIEN Gratuit DE 1 AN Garantie limitée trois ansFrançais DWS535, DWS535T Sierra de 184 mm 7-1/4 pulg. con impulsor sinfínSeguridad en el área de trabajo Definiciones Normas de Seguridad¡ADVERTENCIA! Lea todas las advertencias de seguridad Seguridad eléctricaSeguridad personal Uso y mantenimiento de la herramienta eléctricaInstrucciones de seguridad para todas las sierras MantenimientoCausas del retroceso y su prevención por el operador Instrucciones adicionales de seguridad Instrucciones de seguridad para el protector inferiorCalibre mínimo para juegos de cables Capacidad Componentes Fig Ajuste de la profundidad del corte , 4 Gancho de la sierra FigConector con cierre de torsión DWS535T USO DebidoPara Ajustar LA Sierra Para UN Corte Biselado Ajuste del ángulo del biselAjuste de la plataforma para cortes a 90˚ SI SE Necesita Ajuste AdicionalIndicador de línea de corte Fig Interruptor de gatillo FigPara Abrir EL Orificio PRE-HORADADO Para cambiar las hojasPara Instalar LA Hoja , 10 Español Para Cambiar LA Hoja FIG HojasProtector Inferior DE LA Hoja Dientes Aplicación RetrocesoHoja Soporte Inadecuado DE LA Pieza DE TrabajoApoyo de la pieza de trabajo Fig Advertencia Es importante el apoyarCorte Cortar a LO Largo DE LA Veta FIG Cortes DE Orificios FIGLubricación MantenimientoLimpieza Para Comprobar EL AceiteEscobillas Fig AccesoriosGarantía limitada por tres años ReparacionesPóliza de Garantía ExcepcionesCULIACAN, SIN Año de servicio gratuitoGarantía de reembolso de su dinero por 90 Días GUADALAJARA, JALPUEBLA, PUE MERIDA, YUCMONTERREY, N.L QUERETARO, QRO
Related manuals
Manual 64 pages 58.4 Kb

DWS535 specifications

The DeWalt DWS535 is a powerful and versatile circular saw that is designed to meet the rigorous demands of professionals and DIY enthusiasts alike. Known for its solid construction and cutting-edge technology, the DWS535 showcases the brand's commitment to quality and innovation in woodworking tools.

One of the standout features of the DWS535 is its robust 15-amp motor, which delivers a remarkable no-load speed of 5,300 RPM. This ensures users can tackle a variety of cutting tasks with ease and confidence, whether working with lumber, engineered wood products, or other materials. The high-speed blade cuts through even the toughest materials quickly and efficiently, making it ideal for framing, decking, and general carpentry projects.

The DWS535 is equipped with a 7-1/4 inch carbide-tipped blade that enhances cutting accuracy and durability. The blade's design allows for smooth and clean cuts, reducing the need for post-processing. Additionally, the saw’s integrated electric brake stops the blade quickly after the trigger is released. This safety feature not only enhances user control but also minimizes the risk of accidental injuries, making it a safer choice for operators.

Comfort and usability are also central to the design of the DWS535. It features a lightweight, well-balanced construction that allows for easy maneuverability. Furthermore, the ergonomic handle is designed to reduce fatigue during extended use, providing better grip and control. The saw’s bevel capacity of 0° to 45° contributes to its versatility, enabling users to achieve angled cuts with precision.

Incorporating advanced technologies, the DWS535 features a built-in rafter hook that provides convenient storage and accessibility. Additionally, the saw is designed with a durable protective blade guard that enhances safety while allowing users to easily visualize their cutting line. The tool’s dust port is another thoughtful addition, helping to keep the workspace clean and free from debris, ultimately improving visibility for better accuracy.

Overall, the DeWalt DWS535 stands out in a crowded market of circular saws with its powerful performance, safety features, and user-friendly design. Whether you’re a seasoned professional or a weekend warrior, this tool is engineered to deliver efficiency, accuracy, and safety on every job site. With its remarkable combination of features, the DWS535 proves to be a wise investment for anyone serious about woodworking or construction.