DeWalt Twist-lock Connector DWS535T, Cutting Depth Adjustment , 4, Bevel Angle Adjustment

Page 9

Your saw has a convenient saw hook that allows the saw to hang from a joist, rafter, or other suitable, stable structure. The saw hook folds flat against the tool body when not in use.

To use the saw hook, push down on the hook to rotate it away from the handle until it latches into position.

To return the saw hook to its stored position, pull the hook up until it latches against the tool body.

Twist-lock Connector (DWS535T)

fig. 3

The DWS535T is equipped with a twist-lock connector as shown in Figure 3. This prevents the cord from unplugging if the cord is inadvertantly pulled. Only plug the twist-lock connector into a 3-wire extension cord with a female connector.

Cutting Depth Adjustment (Fig. 1, 4, 5)

1. Hold the saw firmly. Lift the depth adjustment locking lever (B) to

fig. 4

fig. 5

gullet of blade

tip of

btooth

For the most efficient cutting action, set the depth adjustment so that half of a blade tooth will project below the material to be cut. This distance is from the tip of the tooth to the bottom of the gullet in front of it (refer to inset of Figure 5).This keeps blade friction at a minimum, removes sawdust from the cut, results in cooler, faster sawing and reduces the chance of kickback. A method for checking for correct cutting depth is shown in Figure 5. Lay a piece of the material you plan to cut along the side of the blade, as shown, and observe how much tooth projects beyond the material.

Bevel Angle Adjustment (Fig. 1, 6)

English

move foot plate to obtain the desired depth of cut.

2. Lower the depth adjustment locking lever and tighten securely to

lock the depth of cut before operating saw.

The length of cut markings on the side of the foot plate are accurate at full depth of cut only. Setting the saw at the proper cutting depth keeps blade friction to a minimum, removes sawdust from between the blade teeth, results in cooler, faster sawing and reduces the chance of kickback.

The full range of the bevel adjustment is from 0˚ to 53˚. Detents are located at 22.5˚ and 45˚. The angle quadrant is graduated in increments of 1˚. On the front of the saw is a bevel angle adjustment mechanism

Fig. 6

n

i

o

h

7

Image 9
Contents Guide Dutilisation Manual de instrucciones 4 184 mm Worm Drive Saw DWS535, DWS535TWork area safety Definitions Safety GuidelinesElectrical safety InjuryPower tool use and care Personal safetySafety Instructions for All Saws ServiceCauses and Operator Prevention of Kickback Lower Guard Safety Instructions Additional Safety InstructionsAWG Components Fig Saw Hook FigIntended USE Twist-lock Connector DWS535T Cutting Depth Adjustment , 4Bevel Angle Adjustment Kerf Indicator Fig Foot Plate Adjustment for 90˚ CutsTrigger Switch Fig OperationTo remove knockout To Install the Blade , 10To Replace the blade Fig Kickback BladesBlade Teeth ApplicationWorkpiece Support Fig Cutting Ripping Fig Pocket Cutting FigTo check oil Maintenance Cleaning LubricationAccessories Three Year Limited WarrantyYear free service DAY money back GuaranteeEnglish DWS535 et DWS535T, 184 mm 7-1/4 po Scies Circulaires à Vis Sans FinGraves Entraîner des blessures légères ou modérées Définitions lignes directrices en matière de sécuritéRisques de dommages matériels Sécurité du lieu de travailSécurité personnelle Consignes de sécurité propres à toutes les scies Utilisation et entretien d’un outil électriqueRéparation Français Consignes de sécurité relatives au protège-lame inférieur Consignes additionnelles de sécurité240V 120VPlus AWGUsage Prévu Utilisation Ultérieure Description FigConnecteur à verrouillage par rotation DWS535T Crochet de suspension FigRéglage de profondeur de coupe , 4 Avertissement pour réduireRéglage de la plaque d’assise pour des coupes à 90˚ Réglage de l’angle de chanfreinIndicateur de trait de scie Fig Réglage DE LA Scie Pour Effectuer UNE coupe en biseauChangement de lame Gâchette FigRetrait DE l’ALÉSAGE amovible Installation DE LA Lame , 10 Desserrer vers la gauche vers la droite Pour changer LA Lame FigRebonds LamesCarter DE Lame Inférieur LameSupport DE Pièce Inadéquat Configuration DE Profondeur DE Coupe IncorrecteTorsion DE LA Lame Mésalignement DE Coupe Matériaux Nécessitant UNE Attention SpécialeSupport de pièce Fig CoupeAvertissement il est important de sou Coupe longitudinale FIG Entretien NettoyageCoupe interne fig Lubrification Balais FigVérification DE l’huile Service D’ENTRETIEN Gratuit DE 1 AN AccessoiresRéparations Garantie limitée trois ansFrançais Sierra de 184 mm 7-1/4 pulg. con impulsor sinfín DWS535, DWS535T¡ADVERTENCIA! Lea todas las advertencias de seguridad Definiciones Normas de SeguridadSeguridad en el área de trabajo Seguridad eléctricaUso y mantenimiento de la herramienta eléctrica Seguridad personalMantenimiento Instrucciones de seguridad para todas las sierrasCausas del retroceso y su prevención por el operador Instrucciones de seguridad para el protector inferior Instrucciones adicionales de seguridadCalibre mínimo para juegos de cables Capacidad Componentes Fig Conector con cierre de torsión DWS535T Gancho de la sierra FigAjuste de la profundidad del corte , 4 USO DebidoAjuste de la plataforma para cortes a 90˚ Ajuste del ángulo del biselPara Ajustar LA Sierra Para UN Corte Biselado SI SE Necesita Ajuste AdicionalInterruptor de gatillo Fig Indicador de línea de corte FigPara cambiar las hojas Para Abrir EL Orificio PRE-HORADADOPara Instalar LA Hoja , 10 Español Hojas Para Cambiar LA Hoja FIGProtector Inferior DE LA Hoja Hoja RetrocesoDientes Aplicación Soporte Inadecuado DE LA Pieza DE TrabajoAdvertencia Es importante el apoyar Apoyo de la pieza de trabajo FigCorte Cortes DE Orificios FIG Cortar a LO Largo DE LA Veta FIGLimpieza MantenimientoLubricación Para Comprobar EL AceiteAccesorios Escobillas FigPóliza de Garantía ReparacionesGarantía limitada por tres años ExcepcionesGarantía de reembolso de su dinero por 90 Días Año de servicio gratuitoCULIACAN, SIN GUADALAJARA, JALMONTERREY, N.L MERIDA, YUCPUEBLA, PUE QUERETARO, QRO
Related manuals
Manual 64 pages 58.4 Kb

DWS535 specifications

The DeWalt DWS535 is a powerful and versatile circular saw that is designed to meet the rigorous demands of professionals and DIY enthusiasts alike. Known for its solid construction and cutting-edge technology, the DWS535 showcases the brand's commitment to quality and innovation in woodworking tools.

One of the standout features of the DWS535 is its robust 15-amp motor, which delivers a remarkable no-load speed of 5,300 RPM. This ensures users can tackle a variety of cutting tasks with ease and confidence, whether working with lumber, engineered wood products, or other materials. The high-speed blade cuts through even the toughest materials quickly and efficiently, making it ideal for framing, decking, and general carpentry projects.

The DWS535 is equipped with a 7-1/4 inch carbide-tipped blade that enhances cutting accuracy and durability. The blade's design allows for smooth and clean cuts, reducing the need for post-processing. Additionally, the saw’s integrated electric brake stops the blade quickly after the trigger is released. This safety feature not only enhances user control but also minimizes the risk of accidental injuries, making it a safer choice for operators.

Comfort and usability are also central to the design of the DWS535. It features a lightweight, well-balanced construction that allows for easy maneuverability. Furthermore, the ergonomic handle is designed to reduce fatigue during extended use, providing better grip and control. The saw’s bevel capacity of 0° to 45° contributes to its versatility, enabling users to achieve angled cuts with precision.

Incorporating advanced technologies, the DWS535 features a built-in rafter hook that provides convenient storage and accessibility. Additionally, the saw is designed with a durable protective blade guard that enhances safety while allowing users to easily visualize their cutting line. The tool’s dust port is another thoughtful addition, helping to keep the workspace clean and free from debris, ultimately improving visibility for better accuracy.

Overall, the DeWalt DWS535 stands out in a crowded market of circular saws with its powerful performance, safety features, and user-friendly design. Whether you’re a seasoned professional or a weekend warrior, this tool is engineered to deliver efficiency, accuracy, and safety on every job site. With its remarkable combination of features, the DWS535 proves to be a wise investment for anyone serious about woodworking or construction.