Black & Decker CDC1200 Charging the Battery Pack CDC1800 Figure B, Important Charging Notes

Page 7

90516580 CDC9600 CDC1200 etc 4/19/07 9:43 AM Page 7

CHARGING THE BATTERY PACK (CDC1800) FIGURE B

THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power.

1.Plug the charger (7) into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V

AC

2.Slide the charger onto the battery pack (5) as shown in figure B and let the battery pack charge initially for 9 hours. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 9 hours.

3.Unplug charger, and remove the battery pack. Place the battery pack in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place.

NOTE: To remove the battery pack from the drill, press down on the release button (10) on the back of the battery pack (figure D) and slide out.

CHARGING THE BATTERY PACK (CDC9600, CDC1200, CDC1440) FIGURE C

THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power.

1.Make sure the battery pack is fitted properly into the drill. Insert the charger plug (8) into the connector (9) as shown in figure C.

2.Plug the charger into any standard 120 Volt 60 Hz electrical outlet and let the battery pack charge initially for 9 hours. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 9 hours. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC

3.Disconnect the charger from the outlet, then disconnect the charger from the tool.

NOTE: When installing battery pack, be certain that it is inserted fully into the tool cavity until it “clicks” into place.

NOTE: Do not use the tool while it is connected to the charger.

NOTE: To remove the battery pack from the drill, press down on the release button (10) on the back of the battery pack (figure D) and slide out.

IMPORTANT CHARGING NOTES

1.After normal usage, your battery pack should be fully charged in 3 to 9 hours. If the battery pack is run-down completely, it may take up to 9 hours to become fully charged. Your battery pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours.

2.DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above 105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F.(24°C).

3.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

4.If the battery pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C)

(4)If the receptacle and temperature are OK, and you do not get proper charging, take or send the battery pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

5.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its battery pack in a depleted condition.

6.To prolong battery life, avoid leaving the battery pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery life.

7.The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries.

7

Image 7
Contents VEA EL Español EN LA Contraportada Save this Manual for Future ReferenceGeneral Safety Rules Specific Safety Rules Functional Description 90516580 CDC9600 CDC1200 etc 4/19/07 943 AM Battery CAP Information Figure a Safety Warnings and Instructions ChargingImportant Charging Notes Charging the Battery Pack CDC1800 Figure BOperating Instructions Maintenance TroubleshootingRbrc Seal Service Information Full TWO-YEAR Home USE WarrantyConserver CE Manuel Pour UN Usage Ultérieur Mode D’EMPLOIRègles de sécurité générales Règles DE Sécurité Spécifiques Lignes Directrices EN Matière DE Sécurité Définitions Description Fonctionnelle Information Concernant LE Capuchon DU BLOC-PILE FIG. a Chargement DU BLOC-PILES CDC9600, CDC1200, CDC1440 Figure C Chargement DU BLOC-PILES CDC1800 Figure BDétente ET Bouton Inverseur Figure E Directives D’UTILISATIONConseils Importants Concernant LE Chargement Avertissements DE Sécurité ET Directives PerceusesRangement DES Mèches SUR L’OUTIL Correcteur DE Couple Figure FMandrin Sans CLÉ Figure G Pour VisserDépannage EntretienInformation SUR LES Réparations Conserve Este Manual Para Futuras Consultas Números DE CatálogoNormas generales de seguridad Normas DE Seguridad Específicas Pautas DE SEGURIDAD/DEFINICIONES Descripción DE LAS Funciones Advertencias E Instrucciones DE Seguridad Cargar Información Acerca DEL Protector DE LA Batería FIG. aCarga DEL Paquete DE Baterías CDC1800 Figura B Interruptor Disparador Y Botón DE Inversión Figura E Instrucciones DE OperaciónNotas Importantes Sobre LA Carga Instrucciones Y Advertencias DE Seguridad TaladrosEspacio EN LA Herramienta Para Guardar Brocas Control DE Torsión Figura FPortabrocas SIN Llave Figura G AtornilladoMantenimiento Detección DE ProblemasAccesorios 90516580 CDC9600 CDC1200 etc 4/19/07 943 AM MONTERREY, N.L CULIACAN, SINMEXICO, D.F MERIDA, YUC90516580 CDC9600 CDC1200 etc 4/19/07 943 AM 90516580 CDC9600 CDC1200 etc 4/19/07 943 AM 90516580 CDC9600 CDC1200 etc 4/19/07 943 AM