Honeywell HJZTPX user manual FCC Compliance Statement Canadian Compliance Statement

Page 3

FCC COMPLIANCE STATEMENT

Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CANADIAN COMPLIANCE STATEMENT

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

EUROPEAN COMPLIANCE STATEMENT

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CAUTION: Users of the product are responsible for checking and complying with all federal, state and local laws and statutes concerning the monitoring and recording of video and audio signals. Honeywell Video Systems shall not be held responsible for the use of this product in violation of current laws and statutes.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product.

Rev. 1.01	iii	900.0570
		8-Sept-05

Image 3

Contents HJZTP/HJZTPX Issue Date Revisions HJZMU001150900.0570 Explanation of Graphical Symbols FCC Compliance Statement Canadian Compliance StatementEuropean Compliance Statement Important Safeguards Important Safeguards U T I O N Table of Contents Rev Viii 900.0570 Sept-05 PTZ Control Functions When Using Honeywell Maxpro Mode Hjztp Rear Panel List of FiguresSection Introduction Product DescriptionCompatible Products Package Contents Section Installation Connector FunctionConnections Eight-Way RJ45 Connector to Eight-Way RJ45 Connector Eight-Way RJ45 Connector to Green Wire and Blue WireSupplied Cables Daisy chain Dome ConnectionsDome Star Wiring Configuration Star Wiring ConfigurationDVR Setup Multiplexer SetupDVR and Multiplexer Connection Master/Slave Connection Keyboard CascadingConnector PIN Assignments Pin Signal Usual colourSignal Usual colour Power Section Setup Keyboard LockC K E D O T LCD DisplayA V E Y B O a R D System SetupT C C K T RC K 2 DVR/Multiplexer/Camera ConnectionCAM DVR MUX Dome PTZ Protocol C K =O C O L DVR Menus DVR ModeNumber Entry for Entering Passwords Section DVR Control FunctionsPicture Control Camera SelectionDVR Selection Key Function User Level Required Recording and PlaybackSpot Function Alarm FunctionLive Multiplexer ModeSection Multiplexer Control Functions MenusPop Up Menu Bottom MenuFull 2x2 3x3 4x4 PIPLCD Auxiliary Monitor SelectionMultiplexer Selection PTZ Mode PTZ Camera Selection ControlPAN and Tilt Honeywell VCL Protocol Focus and IrisWASH, Wipe and Auxiliary Functions Presets and Tours To Define a PresetTo Seek a Preset To Start a Tour of Presets To Define a Simple TourTo Vary the Standard Speed of a Tour To Vary the Standard Speeds and Dwell Times of a Tour Enhanced Functions V a C YC K O M M E O F F Privacy Zones HomeU R M E T E M E OM E R a R E S E T Digital Zoom Remote ResetW E R U P R E S E T Factory Reset C T O R Y R E S E T Camera ResetO R M I C Rev 900.0570 Sept-05 PTZ Camera Selection Honeywell Diamond Protocol Honeywell Diamond Protocol PAN and Tilt FocusPreshot Definition Flashback Honeywell Diamond Protocol Preshot SeekVectorscan Selection FreezeOn Screen Display OSD Menus Honeywell Diamond Protocol NightshotReturn to Manual Mechanical HomeX T G E Honeywell Diamond Protocol On Screen Display OSD MenusE W P R G G R a M S T= S E N D K = Flashback Operation IntroductionControlling Scan Assemblies Freeze / Unfreeze VideoKD6/HD6 Maxpro Mode PreshotsPreprogrammed Preshots Run VectorScan Vectorscans Video TourProgramming Sector IDS Programming Privacy ZonesPTZ Tour Operation Programming PTZ ToursHjztp / Hjztpx Section Technical SpecificationsRev 900.0570 Sept-05 Appendix a Menu Navigation Rev 900.0570 Sept-05 Appendix B Diagnostics Joystick Auto CalibrationKEY Test Rev 900.0570 Sept-05 Appendix C VCL ORBITER/RAPIDDOME Data Input Rev 900.0570 Sept-05 Appendix D Passwords Blankenbaker Pkwy, Suite Honeywell Video Systems Head Office