Extron electronic MLC 62 IR D manual Mounting an MLC 64 RS VC D to a Decora Mounting Bracket

Page 40

Mounting an MLC 64 RS VC D to a Decora Mounting Bracket

A two-gang Decora mounting bracket is provided with the MLC 64. To mount the MLC 64 to this type of bracket:

1.Cut a hole in the mounting surface large enough to accommodate the provided two-gang mounting bracket.

2.Insert the mounting bracket into the hole.

3.Turn the two screws on the bracket so that the locking arms rotate behind the mounting surface until they clamp securely to it. Do not overtighten.

4.Run the cables through the mounting bracket and attach them.

5.Place the MLC 64 and the volume control module side-by-side onto the bracket so that the centers of the oval screw holes at the top and bottom of both module boards line up with the four holes on the bracket.

6.Insert the four provided silver, rounded Phillips head screws through the oval holes in the two MLC boards and then the round holes in the Decora mounting bracket behind, and tighten the screws.

7.Place the wallplate over the two MLC modules. The front panels should protrude through the slots in the wallplate, while the two boards fit into the recessed area on the back side of the wallplate.

8.Fasten the wallplate onto the MLC boards, using the four provided black or white screws in the holes at the top and bottom of the wallplate.

Wall

4.06"

3.75"

Y
DISPLA	OF	F
	OF
ON
PC
	P
LAPTO
VIDEO
AU	X
AU

Wall Mouting

Bracket

VOLUME

E

MUT

MLC 64 VC D

Wallplate

Figure 40. Mounting an MLC 64 D to a Two-gang Decora Mounting Bracket

MLC 60 Series MediaLink Controllers • Features, Installation, and Operation

34

Image 40

Contents MLC 60 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Software CommandsNotifications Contents MLC 60 Series MediaLink Controllers Contents About the MLC 60 Series MediaLink Controllers About This GuideMLC Models MLC 62 RS EU Features Faceplate alternativesVolume adjustment MLC Configuration Software Device Drivers Application DiagramsMLC 62 IR D Controlling a Projector System Requirements ExtronFeatures Installation, Operation Installation OverviewFront and Left Side Panels MLC D Front PanelsMLC 62 D front panels MLC 64 RS VC D front panelMLC 62 RS EU and MLC 62 RS MK Front and Side Panels Controls behind the wallplateFront panel features Buttons Rear Panel Features MLC 60 Series D Models Rear PanelsPort B IR/S Rear Panel Features on MLC 62 RS EU and MLC 62 RS MK Only MLC 64 RS VC D Volume Control Module Rear PanelRemoving and Replacing the Faceplates InstallationRemoving and replacing an MLC D faceplate Removing the Faceplate MLC 60 Series D Models Replacing the MLC 64 volume control knob Removing the MLC 64 Volume Control Module Faceplate Removing and replacing the MLC 62 RS EU and MK faceplatesReplacing Buttons Replacing the Faceplate MLC 62 RS EUConnecting to Port a RS-232 Wiring for RS-232 Control RS Models OnlyConnecting to Port B IR/S Wiring for IR Control Wiring the Relays Port RS Models OnlyWiring the Digital Input Port RS Models Only MLCWiring the Host/Config Port Connecting a Two-position Switch to the Digital Input PortWiring the Volume Control Module MLC 64 RS VC D Only Connecting Power to the MLCConfiguring the MLC via the USB Port Connecting a Power Supply to an MLCUSB Port Connection for MLC 62 RS EU and MLC 62 RS MK Page IR Learning IR Learning on an MLC D ModelMounting an MLC 62 D Mounting the MLC 60 Series ControllersMounting an MLC 62 D to an electrical junction box Mounting an MLC 62 D to a Decora Mounting Bracket Mounting an MLC 62 D to a Decora Mounting BracketMounting the MLC 64 RS VC D Mounting an MLC 64 RS VC D to an electrical junction boxMounting an MLC 64 RS VC D to a Decora Mounting Bracket Mounting an MLC 64 D to a Two-gang Decora Mounting BracketMounting the MLC 62 RS EU and the MLC 62 RS MK Mounting the MLC 62 RS EU to an Electrical BoxMounting the MLC EU in a Raceway Using Spacers Optional Mounting the MLC 62 RS MK to an External Electrical BoxMounting the MLC 62 RS EU Using a Spacer Accessing Covered Panel Features After Mounting Accessing the Covered MLC D Front Panel FeaturesLocking Using the Front Panel Buttons Front Panel Security LockoutResetting to the default configuration Resetting the MLC Using the Reset ButtonResetting to the factory firmware defaults About the MLC Configuration Program Computer System RequirementsDownloading and Installing the Software from the Web Installing the Configuration SoftwareInstalling the Software from the DVD Starting the Configuration Software Start Options WindowAdd Device Window with Select Model Menu Displayed Accessing the Help File Downloading Drivers Using the Configuration Program Obtaining Device DriversDriver Subscription Window Driver Subscription Download Screen Downloading Drivers from the Disc Drivers Tab and Button on the Software DVD Opening ScreenMLC 60 Device Drivers Page on DVD To download the driver packageTo download a single driver Saving a Single Driver to the ComputerDownloading Drivers from the Web Entering MLC 60 Series Driver Search Criteria Host-to-Controller Communications Error ResponsesController-initiated Messages Using the Command and Response Table Symbol DefinitionsX2# X2% MLC 60 Series MediaLink Controllers SIS Control Command Ascii Command Response Additional Description Command and Response Table for SIS CommandsButton Selection Front Panel Lockout Executive Mode Relay Functions RS models onlyDigital Input Data Port RS models only Device NamingReset/Erase Information RequestsQuery LED status = Button row 4, second LED = Button row 4, third LEDSpecifications MLC 62 Series SpecificationsControl digital input monitoring port RS models GeneralMLC 62 RS EU EMI/EMC MLC 64 RS VC D Specifications MLC 64 RS D Warranty Included Parts Replacement Part Number Part Numbers and AccessoriesIncluded Parts MLC 62 RS EU MLC 64 RS VC D Accessories Accessories Part Number For ModelUSA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe

Related manuals

Manual 4 pages 23.22 Kb