Extron electronic MLC 62 IR D manual Accessing Covered Panel Features After Mounting

Page 44

Accessing Covered Panel Features After Mounting

After the MLC is installed in the mounting surface, you can still access the covered front panel features on the MLC D and the side and rear panel features on the MLC 62 RS EU and MLC 62 RS MK, using the following procedures.

Accessing the Covered MLC D Front Panel Features

After the MLC D is mounted, the following front panel items are covered by the wallplate: IR sensor, DIP switches, Reset button, and USB connector. To access these controls, remove the two screws at the top and bottom of the wallplate and lift it off the MLC, as shown below.

Y

 

DISPLA

OF

F

 

 

ON

VOLUME

VIDEO

PC

MUTE

LAPTOP

MLC 62 D

Wallplate

Figure 44. Removing the MLC D Wallplate

Accessing MLC 62 RS EU and MLC 62 RS MK Side and Rear Panel Features

To access the MLC 62 RS EU or MK side and rear panel features after the MLC has been mounted, you must remove the MLC from the installation surface, leaving the metal mounting bracket attached. (Without the MLC unit to hold it in place, the wall frame also is removed.) A removal tool (shown at right) is provided with the product.

To remove the MLC from the mounting surface:

1.Insert the flat tip of the removal tool in the center of the right or left edge of the MLC, between the MLC and the wall frame, all the way to the line below the arrow on the

tool.

MLC 60 Series MediaLink Controllers • Features, Installation, and Operation

38

Image 44
Contents MLC 60 Series Safety Instructions English FCC Class a Notice Notifications Software CommandsConventions Used in this Guide Contents MLC 60 Series MediaLink Controllers Contents MLC Models About This GuideAbout the MLC 60 Series MediaLink Controllers MLC 62 RS EU Features Faceplate alternativesVolume adjustment MLC Configuration Software Device Drivers Application DiagramsMLC 62 IR D Controlling a Projector System Requirements ExtronFeatures Installation, Operation Installation OverviewFront and Left Side Panels MLC D Front PanelsMLC 62 D front panels MLC 64 RS VC D front panelMLC 62 RS EU and MLC 62 RS MK Front and Side Panels Controls behind the wallplateFront panel features Buttons Rear Panel Features MLC 60 Series D Models Rear PanelsPort B IR/S Rear Panel Features on MLC 62 RS EU and MLC 62 RS MK Only MLC 64 RS VC D Volume Control Module Rear PanelRemoving and replacing an MLC D faceplate InstallationRemoving and Replacing the Faceplates Removing the Faceplate MLC 60 Series D Models Replacing the MLC 64 volume control knob Removing the MLC 64 Volume Control Module Faceplate Removing and replacing the MLC 62 RS EU and MK faceplatesReplacing Buttons Replacing the Faceplate MLC 62 RS EUConnecting to Port B IR/S Wiring for RS-232 Control RS Models OnlyConnecting to Port a RS-232 Wiring for IR Control Wiring the Relays Port RS Models OnlyWiring the Digital Input Port RS Models Only MLCWiring the Host/Config Port Connecting a Two-position Switch to the Digital Input PortWiring the Volume Control Module MLC 64 RS VC D Only Connecting Power to the MLCConfiguring the MLC via the USB Port Connecting a Power Supply to an MLCUSB Port Connection for MLC 62 RS EU and MLC 62 RS MK Page IR Learning IR Learning on an MLC D ModelMounting an MLC 62 D to an electrical junction box Mounting the MLC 60 Series ControllersMounting an MLC 62 D Mounting an MLC 62 D to a Decora Mounting Bracket Mounting an MLC 62 D to a Decora Mounting BracketMounting the MLC 64 RS VC D Mounting an MLC 64 RS VC D to an electrical junction boxMounting an MLC 64 RS VC D to a Decora Mounting Bracket Mounting an MLC 64 D to a Two-gang Decora Mounting BracketMounting the MLC 62 RS EU and the MLC 62 RS MK Mounting the MLC 62 RS EU to an Electrical BoxMounting the MLC EU in a Raceway Using Spacers Optional Mounting the MLC 62 RS MK to an External Electrical BoxMounting the MLC 62 RS EU Using a Spacer Accessing Covered Panel Features After Mounting Accessing the Covered MLC D Front Panel FeaturesLocking Using the Front Panel Buttons Front Panel Security LockoutResetting to the factory firmware defaults Resetting the MLC Using the Reset ButtonResetting to the default configuration About the MLC Configuration Program Computer System RequirementsInstalling the Software from the DVD Installing the Configuration SoftwareDownloading and Installing the Software from the Web Starting the Configuration Software Start Options WindowAdd Device Window with Select Model Menu Displayed Accessing the Help File Downloading Drivers Using the Configuration Program Obtaining Device DriversDriver Subscription Window Driver Subscription Download Screen Downloading Drivers from the Disc Drivers Tab and Button on the Software DVD Opening ScreenMLC 60 Device Drivers Page on DVD To download the driver packageTo download a single driver Saving a Single Driver to the ComputerDownloading Drivers from the Web Entering MLC 60 Series Driver Search Criteria Controller-initiated Messages Error ResponsesHost-to-Controller Communications Using the Command and Response Table Symbol DefinitionsX2# X2% MLC 60 Series MediaLink Controllers SIS Control Button Selection Command and Response Table for SIS CommandsCommand Ascii Command Response Additional Description Front Panel Lockout Executive Mode Relay Functions RS models onlyDigital Input Data Port RS models only Device NamingReset/Erase Information RequestsQuery LED status = Button row 4, second LED = Button row 4, third LEDSpecifications MLC 62 Series SpecificationsControl digital input monitoring port RS models GeneralMLC 62 RS EU EMI/EMC MLC 64 RS VC D Specifications MLC 64 RS D Warranty Included Parts Part Numbers and AccessoriesIncluded Parts Replacement Part Number MLC 62 RS EU MLC 64 RS VC D Accessories Accessories Part Number For ModelUSA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe
Related manuals
Manual 4 pages 23.22 Kb