Extron electronic MLC 62 IR D manual Using the Command and Response Table, Symbol Definitions

Page 61

Using the Command and Response Table

The Command and Response Table on the following pages lists valid ASCII command codes, the responses of the MLC to the host, and a description of the command function or the results of executing the command. The ASCII to HEX conversion table below is for use with the table.

ASCII to Hex Conversion Table

Space

Symbol Definitions

] = CR/LF (carriage return with line feed) (hex 0D 0A)

}= Soft carriage return (no line feed) (hex 0D; web )

• = Space

E = Escape key (hex 1B; web W)

X! = Button number: 01, 02, 03, 04, 05, 06, 07, 08, 09, or 10

Buttons are numbered from front panel top left (01) to bottom right (10).

NOTE: The Mute button on the MLC 64 VC D cannot be configured; therefore, it has

no number.

X@ = Relay port number

1 = Relay 1

2 = Relay 2

X#

X^

=Pulse length in increments of 0.5 seconds. The default is 1 (0.5 seconds). 1 = 0.5 seconds

2 = 1 second

...

255 130 seconds

=Digital input state 0 = low

1 = high

X* = Firmware version number (displayed to two decimal places: n.nn)

X( = Volume range level (a 3-digit number; for serial drivers with volume tables only)

NOTE: Only positive values are allowed. The volume table levels start with zero.

X1! = Lockout (executive) mode 0 = Off

1 = On

MLC 60 Series MediaLink Controllers • SIS Control

55

Image 61
Contents MLC 60 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Software CommandsNotifications Contents MLC 60 Series MediaLink Controllers Contents About the MLC 60 Series MediaLink Controllers About This GuideMLC Models MLC 62 RS EU Faceplate alternatives FeaturesVolume adjustment Application Diagrams MLC Configuration Software Device DriversMLC 62 IR D Controlling a Projector Extron System RequirementsInstallation Overview Features Installation, OperationMLC D Front Panels Front and Left Side PanelsMLC 64 RS VC D front panel MLC 62 D front panelsControls behind the wallplate MLC 62 RS EU and MLC 62 RS MK Front and Side PanelsFront panel features Buttons MLC 60 Series D Models Rear Panels Rear Panel FeaturesPort B IR/S MLC 64 RS VC D Volume Control Module Rear Panel Rear Panel Features on MLC 62 RS EU and MLC 62 RS MK OnlyRemoving and Replacing the Faceplates InstallationRemoving and replacing an MLC D faceplate Removing the Faceplate MLC 60 Series D Models Replacing the MLC 64 volume control knob Removing and replacing the MLC 62 RS EU and MK faceplates Removing the MLC 64 Volume Control Module FaceplateReplacing the Faceplate MLC 62 RS EU Replacing ButtonsConnecting to Port a RS-232 Wiring for RS-232 Control RS Models OnlyConnecting to Port B IR/S Wiring the Relays Port RS Models Only Wiring for IR ControlMLC Wiring the Digital Input Port RS Models OnlyConnecting a Two-position Switch to the Digital Input Port Wiring the Host/Config PortConnecting Power to the MLC Wiring the Volume Control Module MLC 64 RS VC D OnlyConnecting a Power Supply to an MLC Configuring the MLC via the USB PortUSB Port Connection for MLC 62 RS EU and MLC 62 RS MK Page IR Learning on an MLC D Model IR LearningMounting an MLC 62 D Mounting the MLC 60 Series ControllersMounting an MLC 62 D to an electrical junction box Mounting an MLC 62 D to a Decora Mounting Bracket Mounting an MLC 62 D to a Decora Mounting BracketMounting an MLC 64 RS VC D to an electrical junction box Mounting the MLC 64 RS VC DMounting an MLC 64 D to a Two-gang Decora Mounting Bracket Mounting an MLC 64 RS VC D to a Decora Mounting BracketMounting the MLC 62 RS EU to an Electrical Box Mounting the MLC 62 RS EU and the MLC 62 RS MKMounting the MLC 62 RS MK to an External Electrical Box Mounting the MLC EU in a Raceway Using Spacers OptionalMounting the MLC 62 RS EU Using a Spacer Accessing the Covered MLC D Front Panel Features Accessing Covered Panel Features After MountingFront Panel Security Lockout Locking Using the Front Panel ButtonsResetting to the default configuration Resetting the MLC Using the Reset ButtonResetting to the factory firmware defaults Computer System Requirements About the MLC Configuration ProgramDownloading and Installing the Software from the Web Installing the Configuration SoftwareInstalling the Software from the DVD Start Options Window Starting the Configuration SoftwareAdd Device Window with Select Model Menu Displayed Accessing the Help File Obtaining Device Drivers Downloading Drivers Using the Configuration ProgramDriver Subscription Window Driver Subscription Download Screen Drivers Tab and Button on the Software DVD Opening Screen Downloading Drivers from the DiscTo download the driver package MLC 60 Device Drivers Page on DVDSaving a Single Driver to the Computer To download a single driverDownloading Drivers from the Web Entering MLC 60 Series Driver Search Criteria Host-to-Controller Communications Error ResponsesController-initiated Messages Symbol Definitions Using the Command and Response TableX2# X2% MLC 60 Series MediaLink Controllers SIS Control Command Ascii Command Response Additional Description Command and Response Table for SIS CommandsButton Selection Relay Functions RS models only Front Panel Lockout Executive ModeDigital Input Data Port RS models only Device NamingInformation Requests Reset/Erase= Button row 4, second LED = Button row 4, third LED Query LED statusMLC 62 Series Specifications SpecificationsGeneral Control digital input monitoring port RS modelsMLC 62 RS EU EMI/EMC MLC 64 RS VC D Specifications MLC 64 RS D Warranty Included Parts Replacement Part Number Part Numbers and AccessoriesIncluded Parts MLC 62 RS EU MLC 64 RS VC D Accessories Part Number For Model AccessoriesEurope, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East Europe
Related manuals
Manual 4 pages 23.22 Kb