Extron electronic MLC 62 IR D manual Mounting the MLC EU in a Raceway Using Spacers Optional

Page 42

Wall

Wall Box

Metal Bracket

Frame

Y
DISPLA	F
OF

ON

VOLUME

O

VIDE

PC

MUTE

LAPTOP

MLC 62 MK

Figure 42. Mounting the MLC 62 RS MK to an External Electrical Box

Mounting the MLC EU in a Raceway Using Spacers (Optional)

If you are experiencing difficulty with the MLC EU staying in place when installed in a cable raceway, this may be due to a gap between the metal mounting bracket and the wall frame.

When this gap exists, the tabs on the sides of the MLC do not reach the metal mounting bracket and the MLC does not snap completely into the wall frame.

You can remedy this situation by installing a spacer (provided with the MLC EU) between the metal mounting bracket and the rim of the junction box. This spacer appears very similar to the metal mounting bracket, except that it has holes instead of slots for the mounting screws, it is engraved with the words “Optional Spacer” and “Place behind bracket,” and has a slightly larger center opening than the mounting bracket.

NOTE: Do not attempt to use the spacer in place of the metal mounting bracket.

Because of its larger opening, the spacer will not hold the MLC EU in place in

the wall frame.

MLC 60 Series MediaLink Controllers • Features, Installation, and Operation

36

Image 42

Contents MLC 60 Series Safety Instructions English FCC Class a Notice Software Commands Conventions Used in this GuideNotifications Contents MLC 60 Series MediaLink Controllers Contents About This Guide About the MLC 60 Series MediaLink ControllersMLC Models MLC 62 RS EU Features Faceplate alternativesVolume adjustment MLC Configuration Software Device Drivers Application DiagramsMLC 62 IR D Controlling a Projector System Requirements ExtronFeatures Installation, Operation Installation OverviewFront and Left Side Panels MLC D Front PanelsMLC 62 D front panels MLC 64 RS VC D front panelMLC 62 RS EU and MLC 62 RS MK Front and Side Panels Controls behind the wallplateFront panel features Buttons Rear Panel Features MLC 60 Series D Models Rear PanelsPort B IR/S Rear Panel Features on MLC 62 RS EU and MLC 62 RS MK Only MLC 64 RS VC D Volume Control Module Rear PanelInstallation Removing and Replacing the FaceplatesRemoving and replacing an MLC D faceplate Removing the Faceplate MLC 60 Series D Models Replacing the MLC 64 volume control knob Removing the MLC 64 Volume Control Module Faceplate Removing and replacing the MLC 62 RS EU and MK faceplatesReplacing Buttons Replacing the Faceplate MLC 62 RS EUWiring for RS-232 Control RS Models Only Connecting to Port a RS-232Connecting to Port B IR/S Wiring for IR Control Wiring the Relays Port RS Models OnlyWiring the Digital Input Port RS Models Only MLCWiring the Host/Config Port Connecting a Two-position Switch to the Digital Input PortWiring the Volume Control Module MLC 64 RS VC D Only Connecting Power to the MLCConfiguring the MLC via the USB Port Connecting a Power Supply to an MLCUSB Port Connection for MLC 62 RS EU and MLC 62 RS MK Page IR Learning IR Learning on an MLC D ModelMounting the MLC 60 Series Controllers Mounting an MLC 62 DMounting an MLC 62 D to an electrical junction box Mounting an MLC 62 D to a Decora Mounting Bracket Mounting an MLC 62 D to a Decora Mounting BracketMounting the MLC 64 RS VC D Mounting an MLC 64 RS VC D to an electrical junction boxMounting an MLC 64 RS VC D to a Decora Mounting Bracket Mounting an MLC 64 D to a Two-gang Decora Mounting BracketMounting the MLC 62 RS EU and the MLC 62 RS MK Mounting the MLC 62 RS EU to an Electrical BoxMounting the MLC EU in a Raceway Using Spacers Optional Mounting the MLC 62 RS MK to an External Electrical BoxMounting the MLC 62 RS EU Using a Spacer Accessing Covered Panel Features After Mounting Accessing the Covered MLC D Front Panel FeaturesLocking Using the Front Panel Buttons Front Panel Security LockoutResetting the MLC Using the Reset Button Resetting to the default configurationResetting to the factory firmware defaults About the MLC Configuration Program Computer System RequirementsInstalling the Configuration Software Downloading and Installing the Software from the WebInstalling the Software from the DVD Starting the Configuration Software Start Options WindowAdd Device Window with Select Model Menu Displayed Accessing the Help File Downloading Drivers Using the Configuration Program Obtaining Device DriversDriver Subscription Window Driver Subscription Download Screen Downloading Drivers from the Disc Drivers Tab and Button on the Software DVD Opening ScreenMLC 60 Device Drivers Page on DVD To download the driver packageTo download a single driver Saving a Single Driver to the ComputerDownloading Drivers from the Web Entering MLC 60 Series Driver Search Criteria Error Responses Host-to-Controller CommunicationsController-initiated Messages Using the Command and Response Table Symbol DefinitionsX2# X2% MLC 60 Series MediaLink Controllers SIS Control Command and Response Table for SIS Commands Command Ascii Command Response Additional DescriptionButton Selection Digital Input Data Port RS models only Front Panel Lockout Executive ModeRelay Functions RS models only Device NamingReset/Erase Information RequestsQuery LED status = Button row 4, second LED = Button row 4, third LEDSpecifications MLC 62 Series SpecificationsControl digital input monitoring port RS models GeneralMLC 62 RS EU EMI/EMC MLC 64 RS VC D Specifications MLC 64 RS D Warranty Part Numbers and Accessories Included Parts Replacement Part NumberIncluded Parts MLC 62 RS EU MLC 64 RS VC D Accessories Accessories Part Number For ModelAsia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe

Related manuals

Manual 4 pages 23.22 Kb