Aegis Micro NRC 2.0.1 manual Appendix A- Receiver Configuration, BAE Systems WJ-8723

Page 37

Appendix A- Receiver Configuration

BAE Systems WJ-8723

∙The WJ-8723 must be configured to operate and communicate with the NRC units. This is achieved by configuring the WJ-8723 DIP switches A2S1 and A2S27, 8 to:

o set the receiver mode to SINGLE-DROP mode ￿￿set rocker switches 1-5 of DIP switch A2S2 to 1

oset the serial communications to 19,200 bps

￿￿set rocker switches 1-3 of DIP switch A2S1 to 1,0,0 respectively

∙Once the receiver switch settings have been adjusted, cycle the receiver power for switch settings to become active.

∙Be sure to use the BAE Systems WJ-8723 correct control and audio cables.9

∙Connect the control cable from the RS-232/CTL port (D25F) on the receiver to one of the NRC’s COM ports (RJ-45F). The number of this NRC COM port determines the channel number of that receiver.

∙Connect the audio cable from the AUDIO OUT/AUX port on the receiver to the corresponding RCVR port on the NRC. Be sure to select the RCVR port with the same number as the COM port chosen in the previous step.

TEN-TEC RX-331

∙The RX-331 must be configured to operate and communicate with the NRC units. This is achieved by configuring the RX-331 DIP switches S1 and S210, 8 to:

o set the receiver address to 1

￿￿set rocker switches 1-8 of DIP switch S2 to 0,0,0,0,0,0,0,1 respectively

oset the serial communications to 19,200 bps, , 8 data bits, no parity, and 1 stop bit. ￿￿set rocker switches 1-8 of DIP switch S1 to 0,1,1,1,1,0,0,0 respectively.

∙Once the receiver switch settings have been adjusted, cycle the receiver power for switch settings to become active.

∙Be sure to use the correct control and audio cables for the TEN-TEC RX-331. 11, 12

∙Connect the D25M end of the combined NULL modem/control cable to the RS232, J1 port (D25F) on the receiver and the other end to one of the NRC’s COM ports (RJ-45F). The number of this NRC COM port determines the channel number of that receiver.

∙Connect the audio cable from the J8 port on the receiver to the corresponding RCVR port on the NRC. Be sure to select the RCVR port with the same number as the COM port chosen in the previous step.

7Full Instructions on page 2-9 of the “ Installation and Operation Manual for the WJ-8723 Digital HF Receiver” Manual

8Switch settings: 1 is UP/ON, 0 is DOWN/OFF.

9These cables can be obtained from Aegis Inc.

10Refer to page 4-12 of the “ HF DSP Receiver Model RX-331 - Technical Manual” for full instructions

11These cables can be obtained from Aegis Inc.

12To convert between TEN-TEC RX-331 and WJ-8723 control cables requires a standard RS-232 crossover to be used in conjunction with the DB25-RJ45 cable

Users’ Guide: Networked Receiver Controller - NRC-2.0.1

PAGE 37

11th October 2005

Copyright © 2005 Aegis, Inc

wwww.aegis-inc.net [ph. 240-568-9006]

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Networked Receiver Controller NRC-2.0.1 Proprietary Statement Table of Contents TEN-TEC RX-331 General Information Audio Data Capture Channel ArchitectureUniversal Receiver Translation/Abstraction Capabilities Summary Receiver Controllable Settings Client Connection OptionsSystem Hardware Supported Receivers SpecificationsTh October Copyright 2005 Aegis, Inc Contents InstallationHardware Installation Prerequisites NRC ConfigurationConnect to the NRC Change Administrator Password Set the Time and Date Configure Network SettingsConfigure the Network Time Daemon Optional Restart the NRC Set the Host NameUsers’ Guide Networked Receiver Controller NRC-2.0.1 Configure the NRC for Receivers Power-On Self Test Post Using the NRCStarting the NRC Interpreting the LCD DisplayUsers’ Guide Networked Receiver Controller NRC-2.0.1 Connect to NRC Server Dialog Requirements Running the NRC Java ClientMain Application Window TreeNRC Servers Node Content PanelUsers’ Guide Networked Receiver Controller NRC-2.0.1 Channel Node Users’ Guide Networked Receiver Controller NRC-2.0.1 Users’ Guide Networked Receiver Controller NRC-2.0.1 Toolbar Status Bar Change Receiver Model Dialog Change Antenna Model Dialog NRC Properties Dialog Options DestinationCapture Channel Data Dialog Signal Display Dialog Th October Copyright 2005 Aegis, Inc BAE Systems WJ-8723 Appendix A- Receiver ConfigurationNRC File System Appendix B Software UpgradesRestore Command Update CommandUpgrade Procedure Clean CommandUsers’ Guide Networked Receiver Controller NRC-2.0.1 Users’ Guide Networked Receiver Controller NRC-2.0.1
Top Page Image Contents