Configuration 3: R8si<—x.25 —> R8r Gateway

 

3 C-LAN Administration

<—ethernet—> R8si

 

 

 

 

 

 

 

 

 

 

Switch 1 Task — Assign pdm Data Module

 

 

 

 

 

 

This task administers a pdm data module for the connection between the PGATE

 

 

 

 

board and the DS1 board for the connection to node-2. The data module associates a

 

 

 

 

link number with a port address and extension number for the PGATE port used for

 

 

 

 

this connection.

 

 

 

 

 

 

 

 

 

 

Steps

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Begin

 

 

 

 

 

 

 

 

 

 

> Open the Data Module form — enter a da n

 

 

 

 

 

 

 

 

 

 

 

 

 

 

add data-module next

 

 

 

 

 

Page 1 of 2

 

 

 

 

 

 

 

Data Module

 

 

Data Extension: 30

Name: pdm on port 1c0102

 

BCC:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type: pdm_________

COS: 1

Remote Loop-Around Test? n

 

 

 

Port: 01C0102

COR: 1

Secondary data module? n

 

 

 

ITC: restricted__

TN: 1

 

Connected to: dte

ABBREVIATED DIALING

 

 

 

 

 

 

List1:

 

 

 

 

 

 

 

 

 

 

 

 

SPECIAL DIALING OPTION:

 

 

 

 

 

 

ASSIGNED MEMBER (Station with a data extension button for this data module)

 

Ext

 

Name

 

 

 

 

 

 

1: 1002

 

station name

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

> Enter values

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Field

 

 

 

Conditions/Comments

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Type:

 

 

 

This indicates the data-module type for this connection.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port:

 

 

 

This example means that the PGATE circuit pack is in

 

 

 

 

 

 

 

 

 

 

slot 01c01 and link 5 uses port 02.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ITC:

 

 

 

Enter restricted. (unrestricted is used only for

 

 

 

 

 

 

 

 

 

 

wideband transmission.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name:

 

 

 

Information-only; appears in list generated by the “list

 

 

 

 

 

 

 

 

 

 

data module” command.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COS:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The values for these fields will be specified by the

 

 

 

 

 

COR:

 

 

 

 

 

 

 

 

 

 

 

system administrator.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TN:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remote Loop-Around

 

 

Set to n unless testing.

 

 

 

 

 

 

 

Test?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 of 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Administration for Network Connectivity

102

CID: 77730

555-233-504 — Issue 1 — April 2000

Page 122
Image 122
Lucent Technologies Release 8.2 manual Switch 1 Task Assign pdm Data Module, Itc