Configuration 5B: R8csi <—ppp—> R8r (2 C-LANs)

3 C-LAN Administration

<—ethernet—> R8si

 

Switch 1 Task — Assign Processor Channels

This task associates data links (hardware) with processor channels (software) on Switch 1. Note that there are no processor channels or interface channels associated with the ppp connection between the two C-LAN circuit packs.

Steps

 

 

 

Begin

 

 

 

 

 

 

 

 

 

 

 

> Open the Processor Channel Assignment form — enter

ch com p.

 

 

 

 

 

 

change communications-interface processor-channels

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 1 of X

 

 

 

 

 

PROCESSOR CHANNEL ASSIGNMENT

 

 

 

Proc

 

 

Gtwy

 

Interface

Destination

Session

Mach

Chan Enable

Appl. To

Mode

Link/Chan

Node

Port

Local/Remote

ID

1:

n

_______

_

__

_____

_________

0____

___

___

__

2:

n

_______

_

__

_____

_________

0____

___

___

__

3:

n

_______

_

__

_____

_________

0____

___

___

__

:

 

 

 

 

 

 

 

 

 

 

 

12:

y

dcs____

s

1_

5003_

node-2___

0

12_

21_

2_

13:

y

dcs ___

s

2

5003__

node-3___

0

13_

31_

3_

:

 

 

 

 

 

 

 

 

 

 

 

384:

n

_______

_

__

_____

_________

0____

___

___

__

 

 

 

 

 

 

 

 

 

 

 

 

> Enter values

Field

Conditions/Comments

 

Processor Channel 12: (ppp connection to Switch 2)

 

 

Enable

Set to y.

 

 

 

 

 

 

 

 

Appl.

Set to dcs for DCS signaling.

 

 

 

 

 

Mode

Node-1a is the “server” for this session. Set node-2 to “client”

 

 

(c).

 

 

 

 

 

 

 

 

Interface Link

This must match the link number assigned on the node-1a

 

 

data module screen.

 

 

 

 

 

 

 

 

Interface Chan

For TCP/IP, interface channel numbers are in the range 5000

 

 

– 64500.

 

 

 

 

 

The recommended values are: 5001 for CMS, 5002 for Intuity

 

 

AUDIX, and 5003 for DCS connections that are not

 

 

gateways. These three values should be reused for multiple

 

 

instances of these applications; for example, if there are two

 

 

Intuity AUDIX’s, use 5002 for both; or if there are four

 

 

DEFINITY ECS’s, use 5003 for all four. The combination of

 

 

Link, Interface Channel, and Mach ID must be unique.

 

 

This number must match the Destination Port number on the

 

 

Switch-2 Processor Channel screen

 

 

 

 

 

 

 

1 of 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Administration for Network Connectivity

184

 

CID: 77730

555-233-504 — Issue 1 — April 2000

Page 204
Image 204
Lucent Technologies Release 8.2 manual 184 CID