Lucent Technologies Release 8.2 manual Issue 1 April CID 157

Models: Release 8.2

1 524
Download 524 pages 28.9 Kb
Page 177
Image 177

Configuration 5A: R8csi <—ppp—> R8r (one C-LAN)

3 C-LAN Administration

<—ethernet—> R8si

 

Switch 2 Task — Enable Bus Bridge Connectivity

This task enables the bus bridge functionality on the C-LAN circuit pack to provide a path between the packet bus and the processor.

Note: Bus Bridge Connectivity is used on the csi model only. This task may have been complete when the C-LAN circuit pack was installed.

Steps

 

Begin

 

 

 

 

 

> Open the Maintenance-Related System Parameters form — enter

ch sys ma

 

> Go to page 2 and skip to the Packet Intf2? field near the bottom of the screen

 

 

 

 

 

 

change system-parameters maintenance

Page

2 of 3

 

 

MAINTENANCE-RELATED SYSTEM PARAMETERS

 

 

MINIMUM MAINTENANCE THRESHOLDS ( Before Notification )

 

 

TTRs: 4

CPTRs: 1

Call Classifier Ports: 0

 

 

MMIs: 0

VCs: 0

 

 

 

 

TERMINATING TRUNK TRANSMISSION TEST ( Extension )

 

 

Test Type 100:

Test Type 102:

Test Type 105:

 

 

ISDN MAINTENANCE

 

 

 

 

 

 

ISDN-PRI Test Call Extension:

 

ISDN-BRI Service SPID:

 

 

DS1 MAINTENANCE

 

 

 

 

 

 

DS0 Loop-Around Test Call Extension:

 

 

 

LOSS PLAN ( Leave Blank if no Extra Loss is Required )

 

 

Minimum Number of Parties in a Conference Before Adding Extra Loss:

 

SPE OPTIONAL BOARDS

 

 

 

 

 

Packet Intf1? y

Packet Intf2? y

 

 

Bus Bridge: 01a04__Inter-Board Link Timeslots Pt0: 6 Pt1: 1 Pt2: 1

 

 

 

 

 

 

 

 

 

> Enter values

 

 

 

 

 

 

 

 

 

 

 

Field

 

Conditions/Comments

 

 

 

 

 

 

 

 

 

Packet Intf2?

 

Enables the bus bridge.

 

 

 

 

 

 

 

 

Bus Bridge:

 

Location of the C-LAN circuit pack. If the system has two

 

 

 

 

C-LANs, only one is administered for bus bridge.

 

 

 

 

 

 

 

Inter-Board

 

Specifies the bandwidth used on the 3 ports of the Inter-Board

 

 

Link Timeslots:

 

Link. The total number of timeslots assigned cannot exceed

 

 

Pt0, Pt1, Pt2

 

11. Pt0 carries PPP traffic and can have 1–9 timeslots. Pt1

 

 

 

 

carries maintenance messages and can have 1–3 timeslots. Pt2

 

 

 

 

carries broadcast messages and can have 1–3 timeslots.

 

 

 

 

 

 

 

 

 

> Submit the screen

 

 

 

 

 

End

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Administration for Network Connectivity

 

 

 

 

555-233-504 — Issue 1 — April 2000

CID: 77730

157

Page 177
Image 177
Lucent Technologies Release 8.2 manual Issue 1 April CID 157