HP J3250M manual HP ProCurve Switch 8000M Device View, Configuration

Page 52

Managing Switches

Configuration

Managing Switches

Figure 7-2. HP ProCurve Switch 8000M Device View

Configuration - Fault Detection

The automatic fault detection feature protects your network from failing because of problems such as network loops, defective cables, transceivers and faulty network interface cards. Network problems are automatically detected and entered in the Alert Log. The Fault Detection page lets you set the sensitivity levels for the actions to be taken when a fault is detected on a port in your network. Switches only have a sensitivity setting for logging network problems. The sensitivity settings are:

High Sensitivity: The device will make an entry in the Alert Log (located in the Status tab) when a network problem of any severity occurs.

Medium Sensitivity: The device will make an entry in the Alert Log when serious network problems occur.

Low Sensitivity: The device will make an entry in the Alert Log only when severe network problems occur. These are problems that may bring the network down.

Never: The device will never make any entries in the Alert Log regardless of the severity of the problem.

7-6

Image 52
Contents HP Hub & Switch Management for OV-UX User GuidePublication Number Contents Alerts Find/Fix/Inform Setting Up Security for a Device HP Hub & Switch Management Admin Information About HP Hub & Switch Management for OV-UX IntroductionFeatures of HP Hub & Switch Management HP Proactive NetworkingControl UptimeSupport for New Switches Several new switches are supported, as described belowTechnical Product Support Technical Product SupportBefore Installing HP Hub & Switch Management for OV-UX Support InformationManagement Station Requirements HardwareSoftware Hub For OV­Required Network Configuration Required Network ConfigurationRequired Patches Before Installing HP Hub & Switch ManagementRequired Patches Installation Directories Removing HP Hub & Switch ManagementRemoving HP Hub & Switch Management Management products Introduction to HP Hub & Switch Management HP Hub & Switch Management OverviewDefinitions, Processes, and Files HP OpenView Network Management PlatformHP OpenView Network Management Platform Snmp Manager and Agents Definitions, Processes, and FilesWhat HP Devices Can Be Managed HP Devices That Can be ManagedWhat HP Devices Can Be Managed HP J2410A AdvanceStack 100 VG Hub-15NoteHP J3202A AdvanceStack 10Base-T Switching Hub-24RNote HP J3204A AdvanceStack 10Base-T Switching Hub-24TNoteHP J3245A AdvanceStack Switch 800T HP J3298A HP Procurve Switch 212MSnmp Configuration and Snmp MIB Browser Starting the Manager Application Running HP Hub & Switch ManagementStarting HP OpenView Starting the Manager Application DisplayVerifying Installation of the Manager Product Set Verifying Installation of the Manager Product SetMonitor HP Hub/Switch Addressed HP hub, bridge, or switchStopping the Manager Stopping and Restarting the Manager ApplicationStopping and Restarting the Manager Application Use the command /opt/OV/bin/ovstart Restarting the ManagerManagement Alerts Find/Fix/Inform HP Proactive NetworkingControl Alerts Find/Fix/InformUptime PerformanceInterpreting the Alert Log Find/Fix/ Inform Interpreting the Alert Log Find/Fix/InformFind/Fix/Inform Faults Alerts Find/Fix/Inform Log for first time installation information for the device Accessing Hub Features More Information on Device FeaturesAccessing FHub eatures More Information on Device FeaturesAccessing the Device View Accessing Hub FeaturesAccessing the Device View Viewing Device Identity InformationReading the Performance Gauges Interpreting Device StatusSwitching Hub Global Counters Switching Hub Global CountersStatus Global Counters Hub Global CountersConfiguring Your Device Status Port CountersConfiguration Fault Detection Base-T Hub-12M Device ViewConfiguration System Information Fault Detection Sensitivity SettingsHub IP Configuration Configuring IPSwitching Hub IP Configuration Port Configuration Configuration Backup LinksHub Port Configuration Or no violationBackup Link Parameters Configuring Load Balancing Switching Hubs Configuration Support URLBefore the backup port becomes active RetriesAccessing Hub Features Managing Switches Switch StatusManaging Switches Switch StatusSwitch Status Overview Graph AreaAlert Log Area Find/Fix/Inform DescriptionPort Status Settings Status Port StatusConfiguration IdentityDevice View IdentityHP ProCurve Switch 8000M Device View ConfigurationConfiguration IP Configuration Switch IP ConfigurationConfiguration Port Configuration With the device on that port to determine the mode Click on Modify Selected Ports to change the modeFollowing Trkx The port trunk to which this port belongsConfiguration Assigning a Monitoring Port Flow ControlDrops any flow control packets it receives 10/100TX, 10FL, 100FXUsing Vlans Selecting a Monitoring Port on a SwitchConfiguration Device Features Automatic Broadcast Control ABCEnabling Broadcast Control for IP Automatic IP Gateway ConfigurationEnabling Broadcast Control for IPX Internet Group Management Protocol Igmp Spanning Tree Protocol Forward with High PriorityConfiguration Support/Mgmt URLs Support URLManagement Server URL Managing Switches Setting Up Security for a Device Device PasswordsSetting Up Security for a Device Device PasswordsManager/Operator Password Combinations Up Security for a DeviceSetting Up Security Device Manager/Operator Password CombinationsFunction of Community Names Port Security hubs only Address SelectionAddress Selection Port Security hubs onlyAuthorized Address Send AlarmEavesdrop Prevention Disable Port Set Trap Receiver ThresholdsIntrusion Log hubs only Set Security Policy for Selected Ports hubs onlySet Security Policy for Selected Ports hubs only Intrusion Log hubs only Performing Diagnostics Performing DiagnosticsPerforming a Ping/Link Test Performing a Ping/Link TestRebooting a Device Rebooting a DeviceProducing a Configuration Report Resetting a Hub to Factory Default SettingsResetting a Hub to Factory Default Settings Producing a Configuration Report Starting HP Hub & Switch Management Admin HP Hub & Switch Management AdminHP Admin Parameters HP Hub & Switch HP OpenView Device SymbolsNetwork Parameters User Interface Parameters User Interface Parameters Graph Options Parameters Graph Option ParametersPrinter Configuration Parameters Management Admin HP Hub & SwitchOpenView Configuration Options Set As DefaultInstalled Printers list PrinterOpenView Configuration Options Opt/netscape/netscape 10-14 Management for Non-Browserable Devices About Closeup ViewsFor Non Devices Displaying the Closeup ViewAbout Closeup Views Closeup View Areas Title BarMessage Bar ToolbarHub LAN Ports Overview of Toolbar FunctionsSummary of Toolbar Functions Hubs gauges for LAN Activity, Error Packets Switches gauges for LAN Activity, PacketsHub, 100VG hub, 10/100 switch, or bridge Configuration Displays a tabbed dialog box for deviceEnable Port Enables a selected hub port. If a password is Disable PortDisplays the Vlan Configuration window DiagnoseEnabled/Disabled status Status the port is enabled or disabledProperties Change information about a selected Vlan orConfiguration Functions Setting the Configuration ParametersAppendix a Agent Firmware VersionsVerifying Device Agent Versions AAppendixPreparing Network Devices Device Network AddressesAppendix a Preparing Network DevicesConfiguring IP Parameters Globally Assigned IP Network AddressesAppendix a Network Bootp Server Appendix a Index IndexHosts.equiv … 10-13 HP Admin … Packets … 6-5 queriers … 7-14 traffic … Select All Ports … 6-6 Send Alarm … 8-5 sensitivity … 6-7