HP J3250M manual Configuring IP Parameters, Globally Assigned IP Network Addresses

Page 97

Appendix A

Configuring IP Parameters

bridge.

Globally Assigned IP Network Addresses

If you intend to connect your network to other networks that use globally administered IP addresses, Hewlett-Packard strongly recommends that you use IP addresses that have been assigned to you. There is a formal process for assigning unique IP addresses to networks worldwide. Contact one of the following companies:

United States and coun-

Network Solutions, Inc.

1-703-742-4777

tries not in Europe or

Attn: InterNIC Registration Service

questions@internic.net

Asia/Pacific

505 Huntmar Park Drive

http://rs.internic.net

 

 

Herndon, VA 22070

 

 

 

 

Europe

RIPE NCC

+31 20 592 5065

 

Kruislaan 409NL-1098 SJ

ncc@ripe.net

 

Amsterdam

http://www.ripe.net

 

The Netherlands

 

Asia/Pacific

Attention: IN-ADDR.ARPA Registration

 

Asia Pacific Network Information Center

 

c/o Internet Initiative Japan, Inc.

 

Sanbancho Annex Bldg. 1-4

 

Sanban-cho, Chiyoda-ku

 

Tokyo 102, Japan

domreg@apnic.net

http://www.apnic.net

For more information, refer to Internetworking with TCP/IP: Principles,

Protocols and Architecture by Douglas E. Comer (Prentice-Hall, Inc., publisher).

Configuring IP Parameters

To run HP Hub and Switch Management on an IP network, you must configure the management station and all managed devices for IP.

Appendix A

A-3

Image 97
Contents User Guide HP Hub & Switch Management for OV-UXPublication Number Contents Alerts Find/Fix/Inform Setting Up Security for a Device HP Hub & Switch Management Admin Introduction Information About HP Hub & Switch Management for OV-UXHP Proactive Networking Features of HP Hub & Switch ManagementControl UptimeSeveral new switches are supported, as described below Support for New SwitchesTechnical Product Support Technical Product SupportSupport Information Before Installing HP Hub & Switch Management for OV-UXHardware Management Station RequirementsSoftware Hub For OV­Required Network Configuration Required Network ConfigurationRequired Patches Before Installing HP Hub & Switch ManagementRequired Patches Installation Directories Removing HP Hub & Switch ManagementRemoving HP Hub & Switch Management Management products HP Hub & Switch Management Overview Introduction to HP Hub & Switch ManagementDefinitions, Processes, and Files HP OpenView Network Management PlatformHP OpenView Network Management Platform Definitions, Processes, and Files Snmp Manager and AgentsHP Devices That Can be Managed What HP Devices Can Be ManagedWhat HP Devices Can Be Managed HP J2410A AdvanceStack 100 VG Hub-15NoteHP J3204A AdvanceStack 10Base-T Switching Hub-24TNote HP J3202A AdvanceStack 10Base-T Switching Hub-24RNoteHP J3245A AdvanceStack Switch 800T HP J3298A HP Procurve Switch 212MSnmp Configuration and Snmp MIB Browser Starting the Manager Application Running HP Hub & Switch ManagementStarting HP OpenView Display Starting the Manager ApplicationVerifying Installation of the Manager Product Set Verifying Installation of the Manager Product SetMonitor HP Hub/Switch Addressed HP hub, bridge, or switchStopping the Manager Stopping and Restarting the Manager ApplicationStopping and Restarting the Manager Application Restarting the Manager Use the command /opt/OV/bin/ovstartManagement HP Proactive Networking Alerts Find/Fix/InformControl Alerts Find/Fix/InformPerformance UptimeInterpreting the Alert Log Find/Fix/Inform Interpreting the Alert Log Find/Fix/ InformFind/Fix/Inform Faults Alerts Find/Fix/Inform Log for first time installation information for the device More Information on Device Features Accessing Hub FeaturesAccessing FHub eatures More Information on Device FeaturesAccessing Hub Features Accessing the Device ViewAccessing the Device View Viewing Device Identity InformationInterpreting Device Status Reading the Performance GaugesSwitching Hub Global Counters Switching Hub Global CountersStatus Global Counters Hub Global CountersStatus Port Counters Configuring Your DeviceBase-T Hub-12M Device View Configuration Fault DetectionFault Detection Sensitivity Settings Configuration System InformationHub IP Configuration Configuring IPSwitching Hub IP Configuration Configuration Backup Links Port ConfigurationHub Port Configuration Or no violationBackup Link Parameters Configuration Support URL Configuring Load Balancing Switching HubsBefore the backup port becomes active RetriesAccessing Hub Features Switch Status Managing SwitchesManaging Switches Switch StatusGraph Area Switch Status OverviewDescription Alert Log Area Find/Fix/InformStatus Port Status Port Status SettingsIdentity ConfigurationDevice View IdentityConfiguration HP ProCurve Switch 8000M Device ViewSwitch IP Configuration Configuration IP ConfigurationConfiguration Port Configuration Click on Modify Selected Ports to change the mode With the device on that port to determine the modeFollowing Trkx The port trunk to which this port belongsFlow Control Configuration Assigning a Monitoring PortDrops any flow control packets it receives 10/100TX, 10FL, 100FXSelecting a Monitoring Port on a Switch Using VlansAutomatic Broadcast Control ABC Configuration Device FeaturesEnabling Broadcast Control for IP Automatic IP Gateway ConfigurationEnabling Broadcast Control for IPX Internet Group Management Protocol Igmp Forward with High Priority Spanning Tree ProtocolSupport URL Configuration Support/Mgmt URLsManagement Server URL Managing Switches Device Passwords Setting Up Security for a DeviceSetting Up Security for a Device Device PasswordsUp Security for a Device Manager/Operator Password CombinationsSetting Up Security Device Manager/Operator Password CombinationsFunction of Community Names Address Selection Port Security hubs onlyAddress Selection Port Security hubs onlyAuthorized Address Send AlarmEavesdrop Prevention Set Trap Receiver Thresholds Disable PortIntrusion Log hubs only Set Security Policy for Selected Ports hubs onlySet Security Policy for Selected Ports hubs only Intrusion Log hubs only Performing Diagnostics Performing DiagnosticsPerforming a Ping/Link Test Performing a Ping/Link TestRebooting a Device Rebooting a DeviceProducing a Configuration Report Resetting a Hub to Factory Default SettingsResetting a Hub to Factory Default Settings Producing a Configuration Report Starting HP Hub & Switch Management Admin HP Hub & Switch Management AdminHP Admin Parameters HP Hub & Switch HP OpenView Device SymbolsNetwork Parameters User Interface Parameters User Interface Parameters Graph Option Parameters Graph Options ParametersManagement Admin HP Hub & Switch Printer Configuration ParametersSet As Default OpenView Configuration OptionsInstalled Printers list PrinterOpenView Configuration Options Opt/netscape/netscape 10-14 About Closeup Views Management for Non-Browserable DevicesFor Non Devices Displaying the Closeup ViewAbout Closeup Views Title Bar Closeup View AreasMessage Bar ToolbarHub LAN Ports Overview of Toolbar FunctionsSummary of Toolbar Functions Switches gauges for LAN Activity, Packets Hubs gauges for LAN Activity, Error PacketsHub, 100VG hub, 10/100 switch, or bridge Configuration Displays a tabbed dialog box for deviceDisable Port Enable Port Enables a selected hub port. If a password isDisplays the Vlan Configuration window DiagnoseStatus the port is enabled or disabled Enabled/Disabled statusProperties Change information about a selected Vlan orSetting the Configuration Parameters Configuration FunctionsAgent Firmware Versions Appendix aVerifying Device Agent Versions AAppendixDevice Network Addresses Preparing Network DevicesAppendix a Preparing Network DevicesGlobally Assigned IP Network Addresses Configuring IP ParametersAppendix a Network Bootp Server Appendix a Index IndexHosts.equiv … 10-13 HP Admin … Packets … 6-5 queriers … 7-14 traffic … Select All Ports … 6-6 Send Alarm … 8-5 sensitivity … 6-7