HP J3250M manual Required Patches, Before Installing HP Hub & Switch Management

Page 14

Hub &

for OV-

Installing HP

Management

Before

Switch

 

 

Before Installing HP Hub & Switch Management for OV-UX

Required Patches

Required Patches

The following patches must be installed before installing HP Hub & Switch Management for OV-UX. Contact your HP Authorized Dealer or the nearest HP Sales and Support Office, or download the patches from the HP Electronic Support Center. The URL is:

http://us-support2.external.hp.com

The two patches are:

For HP-UX 10.20 — PHSS_15043 S700_800 10.x HP aC++ runtime library components (A.01.15)

For HP-UX 11.00 — S700_800 11.00 HP aC++ runtime library components (A.03.10)

Before Installing HP Hub & Switch

Management

Before you can begin installing HP Hub & Switch Management, you must have successfully completed installing your Network Node Manager product. See the HP OpenView Network Node Manager Products Installation Guide for instructions on installing the HP Network Node Manager and obtaining your software license.

You may set up multiple manager stations on your network. Each manager on which you install the manager product set does its own polling, so the manager traffic on your network will increase in proportion to the number of managers.

Note: This applies only if you buy multiple copies. Your license only entitles you to install one copy.

If you are installing this product set on a workstation with an existing application, be sure you first exit any ovw sessions currently running, then stop all HP OpenView processes using the ovstop command (available to root user).

2-4

Image 14
Contents HP Hub & Switch Management for OV-UX User GuidePublication Number Contents Alerts Find/Fix/Inform Setting Up Security for a Device HP Hub & Switch Management Admin Information About HP Hub & Switch Management for OV-UX IntroductionControl Features of HP Hub & Switch ManagementHP Proactive Networking UptimeSupport for New Switches Several new switches are supported, as described belowTechnical Product Support Technical Product SupportBefore Installing HP Hub & Switch Management for OV-UX Support InformationSoftware Management Station RequirementsHardware Hub For OV­Required Network Configuration Required Network ConfigurationRequired Patches Before Installing HP Hub & Switch ManagementRequired Patches Removing HP Hub & Switch Management Removing HP Hub & Switch ManagementInstallation Directories Management products Introduction to HP Hub & Switch Management HP Hub & Switch Management OverviewHP OpenView Network Management Platform HP OpenView Network Management PlatformDefinitions, Processes, and Files Snmp Manager and Agents Definitions, Processes, and FilesWhat HP Devices Can Be Managed What HP Devices Can Be ManagedHP Devices That Can be Managed HP J2410A AdvanceStack 100 VG Hub-15NoteHP J3245A AdvanceStack Switch 800T HP J3202A AdvanceStack 10Base-T Switching Hub-24RNoteHP J3204A AdvanceStack 10Base-T Switching Hub-24TNote HP J3298A HP Procurve Switch 212MSnmp Configuration and Snmp MIB Browser Starting HP OpenView Running HP Hub & Switch ManagementStarting the Manager Application Starting the Manager Application DisplayMonitor HP Hub/Switch Verifying Installation of the Manager Product SetVerifying Installation of the Manager Product Set Addressed HP hub, bridge, or switchStopping and Restarting the Manager Application Stopping and Restarting the Manager ApplicationStopping the Manager Use the command /opt/OV/bin/ovstart Restarting the ManagerManagement Control Alerts Find/Fix/InformHP Proactive Networking Alerts Find/Fix/InformUptime PerformanceInterpreting the Alert Log Find/Fix/ Inform Interpreting the Alert Log Find/Fix/InformFind/Fix/Inform Faults Alerts Find/Fix/Inform Log for first time installation information for the device Accessing FHub eatures Accessing Hub FeaturesMore Information on Device Features More Information on Device FeaturesAccessing the Device View Accessing the Device ViewAccessing Hub Features Viewing Device Identity InformationReading the Performance Gauges Interpreting Device StatusStatus Global Counters Switching Hub Global CountersSwitching Hub Global Counters Hub Global CountersConfiguring Your Device Status Port CountersConfiguration Fault Detection Base-T Hub-12M Device ViewConfiguration System Information Fault Detection Sensitivity SettingsSwitching Hub IP Configuration Configuring IPHub IP Configuration Hub Port Configuration Port ConfigurationConfiguration Backup Links Or no violationBackup Link Parameters Before the backup port becomes active Configuring Load Balancing Switching HubsConfiguration Support URL RetriesAccessing Hub Features Managing Switches Managing SwitchesSwitch Status Switch StatusSwitch Status Overview Graph AreaAlert Log Area Find/Fix/Inform DescriptionPort Status Settings Status Port StatusDevice View ConfigurationIdentity IdentityHP ProCurve Switch 8000M Device View ConfigurationConfiguration IP Configuration Switch IP ConfigurationConfiguration Port Configuration Following With the device on that port to determine the modeClick on Modify Selected Ports to change the mode Trkx The port trunk to which this port belongsDrops any flow control packets it receives Configuration Assigning a Monitoring PortFlow Control 10/100TX, 10FL, 100FXUsing Vlans Selecting a Monitoring Port on a SwitchConfiguration Device Features Automatic Broadcast Control ABCEnabling Broadcast Control for IPX Automatic IP Gateway ConfigurationEnabling Broadcast Control for IP Internet Group Management Protocol Igmp Spanning Tree Protocol Forward with High PriorityConfiguration Support/Mgmt URLs Support URLManagement Server URL Managing Switches Setting Up Security for a Device Setting Up Security for a DeviceDevice Passwords Device PasswordsManager/Operator Password Combinations Up Security for a DeviceFunction of Community Names Manager/Operator Password CombinationsSetting Up Security Device Address Selection Port Security hubs onlyAddress Selection Port Security hubs onlyEavesdrop Prevention Send AlarmAuthorized Address Disable Port Set Trap Receiver ThresholdsSet Security Policy for Selected Ports hubs only Set Security Policy for Selected Ports hubs onlyIntrusion Log hubs only Intrusion Log hubs only Performing a Ping/Link Test Performing DiagnosticsPerforming Diagnostics Performing a Ping/Link TestRebooting a Device Rebooting a DeviceResetting a Hub to Factory Default Settings Resetting a Hub to Factory Default SettingsProducing a Configuration Report Producing a Configuration Report HP Admin Parameters HP Hub & Switch Management AdminStarting HP Hub & Switch Management Admin Network Parameters HP OpenView Device SymbolsHP Hub & Switch User Interface Parameters User Interface Parameters Graph Options Parameters Graph Option ParametersPrinter Configuration Parameters Management Admin HP Hub & SwitchInstalled Printers list OpenView Configuration OptionsSet As Default PrinterOpenView Configuration Options Opt/netscape/netscape 10-14 Management for Non-Browserable Devices About Closeup ViewsAbout Closeup Views Displaying the Closeup ViewFor Non Devices Message Bar Closeup View AreasTitle Bar ToolbarSummary of Toolbar Functions Overview of Toolbar FunctionsHub LAN Ports Hub, 100VG hub, 10/100 switch, or bridge Hubs gauges for LAN Activity, Error PacketsSwitches gauges for LAN Activity, Packets Configuration Displays a tabbed dialog box for deviceDisplays the Vlan Configuration window Enable Port Enables a selected hub port. If a password isDisable Port DiagnoseProperties Enabled/Disabled statusStatus the port is enabled or disabled Change information about a selected Vlan orConfiguration Functions Setting the Configuration ParametersVerifying Device Agent Versions Appendix aAgent Firmware Versions AAppendixAppendix a Preparing Network DevicesDevice Network Addresses Preparing Network DevicesConfiguring IP Parameters Globally Assigned IP Network AddressesAppendix a Network Bootp Server Appendix a Index IndexHosts.equiv … 10-13 HP Admin … Packets … 6-5 queriers … 7-14 traffic … Select All Ports … 6-6 Send Alarm … 8-5 sensitivity … 6-7