HP
P4459A
manual
HP Part Number
Troubleshooting
Specs
Install
Symbols Used on Equipment
Reset Button
Class a Accessories
Temperature Control
Safety
Powering up a System
Fibre Loop Switch Features
Page 1
HP P4459A
8-Port
Fibre Loop Switch
Installation & Operation Guide
HP Part Number
5971-0861
Printed in February 2001
Page 1
Page 2
Image 1
Page 1
Page 2
Contents
HP Part Number
Audience Assumptions
Symbols Used on Equipment
Safety Instructions
Symbols in Text
Contents
Appendix B Regulatory Information
Related Publications
Preface
Related Web Sites
Fibre Loop Switch Features
Chapter Introducing the HP P4459A Port Fibre Loop Switch
Gbic Ports
Front Panel LEDs
Front View of the Fibre Loop Switch
LEDs
Switching Using Fibre Channel Protocol
Switching Operation
Fibre Channel Arbitration in the Fibre Loop Switch
Fibre Loop Switch Initialization
Introducing the HP P4459A 8-Port Fibre Loop Switch
Page
Unpacking the Fibre Loop Switch
Installing the Fibre Loop Switch
Installing a Gbic
Installing and Removing GBICs Fibre Loop Switch
Remove any cables attached to the Gbic
Removing a Gbic
Rack Installation
Rack Mounting the Fibre Loop Switch
Rack Installation Basics
Mounting in HP Systems Racks
Tools Required
Preparation
Marking Holes and Attaching Barrel Nuts on HP Systems Racks
Place the Barrel Nuts on the Rack Columns
Mark the Rack Column Holes
Installing the Fibre Loop Switch
Attach the Sleeves to the Front Rack Columns
Identify the six Torx screws
Attaching Sleeves to an HP Systems Rack
Installing the Fibre Loop Switch
Securing the Switch Rails to the Switch
Attach the Switch Rails to the Switch Chassis
Install the switch
Installing the Switch into an HP Systems Rack
Connect the appropriate AC power cord to the switch
Complete the Installation
Retract the anti-tip foot, if desired
Cabling for the Fibre Loop Switch
Powering up a System
Copper cable requirements for the Fibre Loop Switch
General Maintenance Considerations
Chapter Fibre Loop Switch Troubleshooting
Reading the LED Indicators
Troubleshooting the Switch
Reading The Power, Fault, and Initialization LEDs
Connections
Reset Button
Fibre Channel Cables
Temperature Control
Fans
Filler Panel
Page
Switching
Appendix a Fibre Loop Switch Functional Specifications
Physical Specifications
Environmental Specifications
LED Specifications
Electrical Specifications
Fibre Channel Communications
Regulatory Certification
Vcci V3 1997, Class a
Page
Regulatory Notices
Appendix B Regulatory Information
Electromagnetic Compliance
Class a Equipment
Class a Accessories
For products labeled as Class a
Class a Warning
Radio Frequency Emissions Warning for Accessories
Declaration of Conformity
Declaration of Conformity US and EU
Regulatory Notices Product Safety
Laser Safety Germany
Class Laser Product Lasser Klasse 1 Produkt
Hardware Accessories Limited Warranty
Appendix C Warranty and Support
Hewlett-Packard Hardware Accessories
Third-Party Hardware Products
HP Repair and Telephone Support
Canada
Other Countries
World Wide Web
Page
Glossary
Transmission sent to all NPorts on a network
ElectroMagnetic Compatibility
FC-PH
Fpga
Time delay of data traffic through a network or a switch
Lilp
Lpsm
OFC
Fibre Channel Arbitrated Loop that is connected to a fabric
SAN
Physical or logical layout of nodes on a network
Related pages
Troubleshooting Points for Poulan 183359
Specifications & Features for Califone CAR2020
Indicator light for IBM 1422
Auto Menu Chart for Sharp R-622STM
When the Menu Contains Two or More Pages for Nikon S6200
Installing New Components for Acer RC500L
Main Electrical Parts List for Sony MZ-N707
Language Code and Area Code List for NEC NDRV-62
What are the symptoms of a touch panel in Standby Mode?
Read about Standby Mode symptoms
Top
Page
Image
Contents