HP P4459A manual Electrical Specifications, LED Specifications, Fibre Channel Communications

Page 46

HP P4459A 8-Port Fibre Loop Switch Installation & Operation Guide

Electrical Specifications

AC Voltage	100–240 VAC autosensing
Frequency	50 to 60 Hz
Rated Input Current	1.5A — 0.7A

LED Specifications

Front Panel LED Indicators

Power	Green
Fault	Amber
Init	Green

Port LED Indicators

Link	Green
Fault	Amber

Fibre Channel Communications

Media	DB-9 Copper, HSSDC Copper, SW Optical
	Dual SC, GBIC
Protocol and Standards	FC-AL, FC-AL-2, FC-PH, FC-PH-2,
	FC-PH-3, FC-PLDA, FCP

Regulatory Certification

Safety Compliance

USA	UL 1950, 1995 3rd Edition
Canada	CSA C22.2 No. 950-95, 3rd Edition
European Union (EU)
and Nordic	EN 60950: 1992 A1/A2/A3/A4/A11
	EMKO-TSE (74-SEC) 207/94
Other Countries:	IEC 60950: A1/A2/A3/A4

EMC Compliance

USA	FCC Title 47 CFR, Part 15, SubpartB; 1998,
	Class A
Canada	ICES-003, Class A

38

Image 46

Contents HP Part Number Audience Assumptions Safety Instructions Symbols Used on EquipmentSymbols in Text Contents Appendix B Regulatory Information Preface Related PublicationsRelated Web Sites Fibre Loop Switch Features Chapter Introducing the HP P4459A Port Fibre Loop SwitchGbic Ports Front View of the Fibre Loop Switch Front Panel LEDsLEDs Switching Operation Switching Using Fibre Channel ProtocolFibre Channel Arbitration in the Fibre Loop Switch Fibre Loop Switch Initialization Introducing the HP P4459A 8-Port Fibre Loop Switch Page Installing the Fibre Loop Switch Unpacking the Fibre Loop SwitchInstalling and Removing GBICs Fibre Loop Switch Installing a GbicRemoving a Gbic Remove any cables attached to the GbicRack Mounting the Fibre Loop Switch Rack InstallationRack Installation Basics Mounting in HP Systems Racks Tools Required Preparation Marking Holes and Attaching Barrel Nuts on HP Systems Racks Mark the Rack Column Holes Place the Barrel Nuts on the Rack ColumnsInstalling the Fibre Loop Switch Attach the Sleeves to the Front Rack Columns Identify the six Torx screws Attaching Sleeves to an HP Systems Rack Installing the Fibre Loop Switch Attach the Switch Rails to the Switch Chassis Securing the Switch Rails to the SwitchInstall the switch Installing the Switch into an HP Systems Rack Complete the Installation Connect the appropriate AC power cord to the switchRetract the anti-tip foot, if desired Powering up a System Cabling for the Fibre Loop SwitchCopper cable requirements for the Fibre Loop Switch Chapter Fibre Loop Switch Troubleshooting General Maintenance ConsiderationsTroubleshooting the Switch Reading the LED IndicatorsReading The Power, Fault, and Initialization LEDs Reset Button ConnectionsFans Temperature ControlFibre Channel Cables Filler PanelPage Physical Specifications Appendix a Fibre Loop Switch Functional SpecificationsSwitching Environmental SpecificationsFibre Channel Communications Electrical SpecificationsLED Specifications Regulatory CertificationVcci V3 1997, Class a Page Regulatory Notices Appendix B Regulatory InformationElectromagnetic Compliance Class a Equipment Class a AccessoriesFor products labeled as Class a Class a Warning Radio Frequency Emissions Warning for Accessories Declaration of Conformity US and EU Declaration of ConformityRegulatory Notices Product Safety Laser Safety Germany Class Laser Product Lasser Klasse 1 Produkt Hardware Accessories Limited Warranty Appendix C Warranty and SupportHewlett-Packard Hardware Accessories Canada HP Repair and Telephone SupportThird-Party Hardware Products Other CountriesWorld Wide Web Page Glossary Transmission sent to all NPorts on a network ElectroMagnetic Compatibility FC-PH Fpga Time delay of data traffic through a network or a switch Lilp Lpsm OFC Fibre Channel Arbitrated Loop that is connected to a fabric SAN Physical or logical layout of nodes on a network