HP P4459A manual Regulatory Notices Product Safety

Page 54

HP P4459A 8-Port Fibre Loop Switch Installation & Operation Guide

Regulatory Notices - Product Safety

This product may be equipped with a Hewlett-Packard Optical GBIC containing a laser. In which case the GBIC is a Class 1 Laser Product per US/FDA/CDRH (21 CFR) and per IEC-825-1 (EN60825-1 and A11).

Laser Safety– United States

CAUTION This device contains a laser system and is classified as a "Class-1 Laser Product" under a U.S. Department of Health and Human Services (DHHS) Radiation Performance standard according to the Radiation Control for Health and Safety Act of 1968.

To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

WARNING Use of controls, adjustments or the performance procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure

Laser Safety - Finland

•LASERTURVALLISUUS

•LUOKAN 1 LASERLAITE

•KLASS 1 LASER APPARAT

46

Image 54

Contents HP Part Number Audience Assumptions Safety Instructions Symbols Used on EquipmentSymbols in Text Contents Appendix B Regulatory Information Preface Related PublicationsRelated Web Sites Chapter Introducing the HP P4459A Port Fibre Loop Switch Fibre Loop Switch FeaturesGbic Ports Front View of the Fibre Loop Switch Front Panel LEDsLEDs Switching Operation Switching Using Fibre Channel ProtocolFibre Channel Arbitration in the Fibre Loop Switch Fibre Loop Switch Initialization Introducing the HP P4459A 8-Port Fibre Loop Switch Page Installing the Fibre Loop Switch Unpacking the Fibre Loop SwitchInstalling and Removing GBICs Fibre Loop Switch Installing a GbicRemoving a Gbic Remove any cables attached to the GbicRack Mounting the Fibre Loop Switch Rack InstallationRack Installation Basics Mounting in HP Systems Racks Tools Required Preparation Marking Holes and Attaching Barrel Nuts on HP Systems Racks Mark the Rack Column Holes Place the Barrel Nuts on the Rack ColumnsInstalling the Fibre Loop Switch Attach the Sleeves to the Front Rack Columns Identify the six Torx screws Attaching Sleeves to an HP Systems Rack Installing the Fibre Loop Switch Attach the Switch Rails to the Switch Chassis Securing the Switch Rails to the SwitchInstall the switch Installing the Switch into an HP Systems Rack Complete the Installation Connect the appropriate AC power cord to the switchRetract the anti-tip foot, if desired Powering up a System Cabling for the Fibre Loop SwitchCopper cable requirements for the Fibre Loop Switch Chapter Fibre Loop Switch Troubleshooting General Maintenance ConsiderationsTroubleshooting the Switch Reading the LED IndicatorsReading The Power, Fault, and Initialization LEDs Reset Button ConnectionsFans Temperature ControlFibre Channel Cables Filler PanelPage Physical Specifications Appendix a Fibre Loop Switch Functional SpecificationsSwitching Environmental SpecificationsFibre Channel Communications Electrical SpecificationsLED Specifications Regulatory CertificationVcci V3 1997, Class a Page Appendix B Regulatory Information Regulatory NoticesElectromagnetic Compliance Class a Accessories Class a EquipmentFor products labeled as Class a Class a Warning Radio Frequency Emissions Warning for Accessories Declaration of Conformity US and EU Declaration of ConformityRegulatory Notices Product Safety Laser Safety Germany Class Laser Product Lasser Klasse 1 Produkt Appendix C Warranty and Support Hardware Accessories Limited WarrantyHewlett-Packard Hardware Accessories Canada HP Repair and Telephone SupportThird-Party Hardware Products Other CountriesWorld Wide Web Page Glossary Transmission sent to all NPorts on a network ElectroMagnetic Compatibility FC-PH Fpga Time delay of data traffic through a network or a switch Lilp Lpsm OFC Fibre Channel Arbitrated Loop that is connected to a fabric SAN Physical or logical layout of nodes on a network