HP P4459A manual LEDs

Page 11

 

Introducing the HP P4459A 8-Port Fibre Loop Switch

 

 

Connector

Figure 2: Fibre Loop Switch front panel

PwerPlug

SwitchStatus￿

PortStatus￿

 

LEDs

LEDs

 

Table 1 describes the operation of the switch LEDs and Table 2 describes the operation of the port LEDs on the front panel of the fibre loop switch.

Table 1: Fibre Loop Switch LEDs

Name

Color

Function

 

 

 

 

 

 

fault

Amber

Indicates that the switch is running a self-test during start-up, or a failure

 

 

occurred.

 

 

 

power

Green

Indicates that power is on to the switch.

 

 

 

Table 2: Port LEDs

Name

Color

Function

 

 

 

 

 

 

Link

Green

Indicates that a good physical link has been established.

 

 

 

Fault

Amber

Indicates that faulty data is being received on the port.

 

 

 

3

Image 11
Contents HP Part Number Audience Assumptions Symbols Used on Equipment Safety InstructionsSymbols in Text Contents Appendix B Regulatory Information Related Publications PrefaceRelated Web Sites Gbic Ports Chapter Introducing the HP P4459A Port Fibre Loop SwitchFibre Loop Switch Features Front Panel LEDs Front View of the Fibre Loop SwitchLEDs Switching Using Fibre Channel Protocol Switching OperationFibre Channel Arbitration in the Fibre Loop Switch Fibre Loop Switch Initialization Introducing the HP P4459A 8-Port Fibre Loop Switch Page Unpacking the Fibre Loop Switch Installing the Fibre Loop SwitchInstalling a Gbic Installing and Removing GBICs Fibre Loop SwitchRemove any cables attached to the Gbic Removing a GbicRack Installation Rack Mounting the Fibre Loop SwitchRack Installation Basics Mounting in HP Systems Racks Tools Required Preparation Marking Holes and Attaching Barrel Nuts on HP Systems Racks Place the Barrel Nuts on the Rack Columns Mark the Rack Column HolesInstalling the Fibre Loop Switch Attach the Sleeves to the Front Rack Columns Identify the six Torx screws Attaching Sleeves to an HP Systems Rack Installing the Fibre Loop Switch Securing the Switch Rails to the Switch Attach the Switch Rails to the Switch ChassisInstall the switch Installing the Switch into an HP Systems Rack Connect the appropriate AC power cord to the switch Complete the InstallationRetract the anti-tip foot, if desired Cabling for the Fibre Loop Switch Powering up a SystemCopper cable requirements for the Fibre Loop Switch General Maintenance Considerations Chapter Fibre Loop Switch TroubleshootingReading the LED Indicators Troubleshooting the SwitchReading The Power, Fault, and Initialization LEDs Connections Reset ButtonFiller Panel Temperature ControlFibre Channel Cables FansPage Environmental Specifications Appendix a Fibre Loop Switch Functional SpecificationsSwitching Physical SpecificationsRegulatory Certification Electrical SpecificationsLED Specifications Fibre Channel CommunicationsVcci V3 1997, Class a Page Electromagnetic Compliance Appendix B Regulatory InformationRegulatory Notices For products labeled as Class a Class a AccessoriesClass a Equipment Class a Warning Radio Frequency Emissions Warning for Accessories Declaration of Conformity Declaration of Conformity US and EURegulatory Notices Product Safety Laser Safety Germany Class Laser Product Lasser Klasse 1 Produkt Hewlett-Packard Hardware Accessories Appendix C Warranty and SupportHardware Accessories Limited Warranty Other Countries HP Repair and Telephone SupportThird-Party Hardware Products CanadaWorld Wide Web Page Glossary Transmission sent to all NPorts on a network ElectroMagnetic Compatibility FC-PH Fpga Time delay of data traffic through a network or a switch Lilp Lpsm OFC Fibre Channel Arbitrated Loop that is connected to a fabric SAN Physical or logical layout of nodes on a network