HP Smart Array Advanced Pack Software manual Replacing the P700m cache battery

Page 56

oIf the LED is not lit, disconnect the battery cable from the cache.

5.Remove the controller from the server and place it on a firm, flat, nonconductive surface.

6.Remove the existing cache from the controller by pulling at both ends of the cache module with equal force.

7.Install the new cache on the controller. Press firmly above each connector to ensure good electrical contact. (If the cache is not connected properly, the controller cannot boot.)

8.Install the controller in the server.

9.If the previous cache was connected to a battery pack, connect the battery cable to the new cache.

Replacing the P700m cache battery

CAUTION: Electrostatic discharge can damage electronic components. Be sure you are properly grounded before beginning this procedure.

Upgrade and replacement procedures 56

Image 56

Contents Abstract Part Number August EditionPage Contents Installation and configuration Regulatory compliance notices Moving drives and arrays Adding drivesComponent identification Controller componentsP212 components DescriptionFor LED locations and status, see P222 LEDs on Description P400 components model with front connectorsP222 components P400 components model with back connectors P410 components P411 componentsP420 components For LED locations and status, see P420 LEDs on DescriptionFor LED locations and status, see P421 LEDs on Description P421 componentsE500 components P700m components P711m components P712m componentsFor LED locations and status, see P721m LEDs on P721m componentsP800 components P812 components Controller board runtime LEDs P822 componentsP212, P410, and P411 LEDs Color Name CommentsE500 and P400 LEDs Idle Task LED status Controller CPU activity levelColor Name Interpretation P222 LEDsP420 LEDs P421 LEDs P700m LEDs Green CR8 Idle TaskP711m LED P712m LEDP721m LEDs P800 LEDsCannot function due to an internal problem. If P812 LEDs Fbwc module LEDs P410, P411, P711m, P812 Fbwc module LEDsP822 LEDs Fbwc module LEDs P222, P420, P421, P721m, P822 Green LED Amber LED InterpretationColor Description Battery pack LEDsAmber Green Interpretation LED3 pattern LED4 pattern Interpretation Specifications Memory and storage capacity conventionsRAID conventions Smart Array Advanced PackSupported servers and server blades Required hardwareSpecifications common to all controller models Feature DetailsController Speed Supported product Server RulesSpecification E500 P411 P421 Controller specifications by modelE500, P411, and P421 specifications P400, P410, and P420 specifications P212 and P222 specificationsSpecification P400 P410 P420 Specification P212 P222P700m, P711m, P712m, and P721m specifications P800, P812, and P822 specificationsSpecification P700m P711m P712M P721m Specification P800 P812 P822Battery pack service life Installing a stand-up controller in an unconfigured server Installation and configurationProcedures for controllers in a server Installing the controller board Connecting internal storage Procedures for controllers in a server blade SAS cable part numbersInstallation and configuration Installing the mezzanine controller board Configuration tools Option ROM Configuration for ArraysArray configuration tools ROM-Based Setup UtilityUpdating firmware System maintenance toolsInstalling device drivers Event Notification Service HP Insight Diagnostics Diagnostic toolsInstalling Management Agents Installation and configuration Upgrade and replacement procedures Replacing the battery on the P212, P410, and P411 modelsReplacing the Fbwc module on the P410 and P411 models Replacing the Bbwc module on the P212, P410, and P411 models Upgrade and replacement procedures Upgrade and replacement procedures Installing an E500 or P400 cache battery Replacing an E500 or P400 cache battery Replacing the E500 or P400 cache Replacing the P700m cache battery Upgrade and replacement procedures Upgrade and replacement procedures Removing a P711m capacitor pack Replacing a P711m cache module Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P712m cache module Replacing the Fbwc module on the P721m Replacing a P800 cache battery Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Replacing the P800 cache module or controller Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P812 cache module Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P822 cache module Upgrade and replacement procedures Drive procedures Identifying the status of a legacy driveIdentifying the status of an HP SmartDrive Status DefinitionRecognizing drive failure Effects of a drive failureReplacing drives Compromised fault toleranceRecovering from compromised fault tolerance Automatic data recovery rebuild Before replacing drivesTime required for a rebuild Abnormal termination of a rebuild Upgrading drive capacity Restore data from backupMoving drives and arrays Adding drives Drive procedures Grounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Regulatory compliance notices Federal Communications Commission noticeFCC rating label FCC Notice, Class a EquipmentCanadian notice Avis Canadien ModificationsCables European Union regulatory notice Bsmi noticeBattery replacement notice Chinese noticeJapanese notice Korean notice Class a equipmentTaiwan battery recycling notice Acronyms and abbreviations HP Service Pack for ProLiant System Management HomepageDocumentation feedback Index CpqonlinFederal Communications Commission FCC Smart Array Advanced Pack Saap