HP Smart Array Advanced Pack Software manual LED3 pattern LED4 pattern Interpretation

Page 29

LED3 pattern

LED4 pattern

Interpretation

 

 

 

Off

Flashing (2 Hz)

The system is powered down, and the cache contains data that has not

 

 

yet been written to the drives. Restore system power as soon as

 

 

possible to prevent data loss.

 

 

Data preservation time is extended any time that 3.3 V auxiliary

 

 

power is available, as indicated by LED 2. In the absence of auxiliary

 

 

power, battery power alone preserves the data. A fully-charged

 

 

battery can normally preserve data for at least 2 days.

 

 

The battery lifetime also depends on the cache module size. For more

 

 

information, see the controller QuickSpecs on the HP website

 

 

(http://www.hp.com).

 

 

 

Off

Double flash, then

The cache microcontroller is waiting for the host controller to

 

pause

communicate.

Off

Flashing (1 Hz)

The battery pack is below the minimum charge level and is being

 

 

charged. Features that require a battery (such as write cache, capacity

 

 

expansion, stripe size migration, and RAID migration) are unavailable

 

 

temporarily until charging is complete. The recharge process takes

 

 

between 15 minutes and 2 hours, depending on the initial capacity of

 

 

the battery.

 

 

 

Off

On

The battery pack is fully charged, and posted write data is stored in the

 

 

cache.

 

 

 

Off

Off

The battery pack is fully charged, and no posted write data exists in

 

 

the cache.

Flashing (1 Hz)

Flashing (1 Hz)

An alternating green and amber flashing pattern indicates that the

 

 

cache microcontroller is executing from within its boot loader and

 

 

receiving new flash code from the host controller.

 

 

 

On

A short circuit exists across the battery terminals or within the battery

 

 

pack. BBWC features are disabled until the battery pack is replaced.

 

 

The life expectancy of a battery pack is typically more than 3 years.

 

 

 

Flashing (1 Hz)

An open circuit exists across the battery terminals or within the battery

 

 

pack. BBWC features are disabled until the battery pack is replaced.

 

 

The life expectancy of a battery pack is typically more than 3 years.

 

 

 

Component identification 29

Image 29
Contents Part Number August Edition AbstractPage Contents Installation and configuration Moving drives and arrays Adding drives Regulatory compliance noticesController components Component identificationP212 components DescriptionFor LED locations and status, see P222 LEDs on Description P400 components model with front connectorsP222 components P400 components model with back connectors P411 components P410 componentsFor LED locations and status, see P420 LEDs on Description P420 componentsFor LED locations and status, see P421 LEDs on Description P421 componentsE500 components P700m components P712m components P711m componentsFor LED locations and status, see P721m LEDs on P721m componentsP800 components P812 components P822 components Controller board runtime LEDsColor Name Comments P212, P410, and P411 LEDsIdle Task LED status Controller CPU activity level E500 and P400 LEDsColor Name Interpretation P222 LEDsP420 LEDs P421 LEDs Green CR8 Idle Task P700m LEDsP712m LED P711m LEDP800 LEDs P721m LEDsCannot function due to an internal problem. If P812 LEDs Fbwc module LEDs P410, P411, P711m, P812 Fbwc module LEDsP822 LEDs Green LED Amber LED Interpretation Fbwc module LEDs P222, P420, P421, P721m, P822Color Description Battery pack LEDsAmber Green Interpretation LED3 pattern LED4 pattern Interpretation Memory and storage capacity conventions SpecificationsRAID conventions Smart Array Advanced PackRequired hardware Supported servers and server bladesFeature Details Specifications common to all controller modelsController Speed Supported product Server RulesSpecification E500 P411 P421 Controller specifications by modelE500, P411, and P421 specifications P212 and P222 specifications P400, P410, and P420 specificationsSpecification P400 P410 P420 Specification P212 P222P800, P812, and P822 specifications P700m, P711m, P712m, and P721m specificationsSpecification P700m P711m P712M P721m Specification P800 P812 P822Battery pack service life Installing a stand-up controller in an unconfigured server Installation and configurationProcedures for controllers in a server Installing the controller board Connecting internal storage SAS cable part numbers Procedures for controllers in a server bladeInstallation and configuration Installing the mezzanine controller board Option ROM Configuration for Arrays Configuration toolsROM-Based Setup Utility Array configuration toolsUpdating firmware System maintenance toolsInstalling device drivers Event Notification Service HP Insight Diagnostics Diagnostic toolsInstalling Management Agents Installation and configuration Replacing the battery on the P212, P410, and P411 models Upgrade and replacement proceduresReplacing the Fbwc module on the P410 and P411 models Replacing the Bbwc module on the P212, P410, and P411 models Upgrade and replacement procedures Upgrade and replacement procedures Installing an E500 or P400 cache battery Replacing an E500 or P400 cache battery Replacing the E500 or P400 cache Replacing the P700m cache battery Upgrade and replacement procedures Upgrade and replacement procedures Removing a P711m capacitor pack Replacing a P711m cache module Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P712m cache module Replacing the Fbwc module on the P721m Replacing a P800 cache battery Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Replacing the P800 cache module or controller Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P812 cache module Upgrade and replacement procedures Upgrade and replacement procedures Upgrade and replacement procedures Replacing a P822 cache module Upgrade and replacement procedures Identifying the status of a legacy drive Drive proceduresStatus Definition Identifying the status of an HP SmartDriveEffects of a drive failure Recognizing drive failureReplacing drives Compromised fault toleranceRecovering from compromised fault tolerance Before replacing drives Automatic data recovery rebuildTime required for a rebuild Abnormal termination of a rebuild Upgrading drive capacity Restore data from backupMoving drives and arrays Adding drives Drive procedures Grounding methods to prevent electrostatic discharge Electrostatic dischargePreventing electrostatic discharge Federal Communications Commission notice Regulatory compliance noticesFCC rating label FCC Notice, Class a EquipmentCanadian notice Avis Canadien ModificationsCables Bsmi notice European Union regulatory noticeChinese notice Battery replacement noticeJapanese notice Korean notice Class a equipmentTaiwan battery recycling notice Acronyms and abbreviations System Management Homepage HP Service Pack for ProLiantDocumentation feedback Cpqonlin IndexFederal Communications Commission FCC Smart Array Advanced Pack Saap