HP Scitex LX800 Industrial manual Safety precautions, General safety guidelines

Page 5

1 Safety precautions

Before installing the printer, read the following safety precautions.

General safety guidelines

No operator serviceable parts inside. Refer servicing to qualified service personnel.

Turn off the printer, using both Branch Circuit Breakers located in the building's Power Distribution Unit (PDU), and call your service representative in any of the following cases:

The power cord is damaged.

Liquid has entered the printer.

There is smoke or an unusual smell coming from the printer.

The printer has been dropped or the drying or curing module damaged.

The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has repeatedly tripped.

Fuses have blown.

The printer is not operating normally.

Turn off the printer using both Branch Circuit Breakers in either of the following cases:

During a thunderstorm

During a power failure

Electric shock hazard

WARNING! The internal circuits and drying and curing modules operate at hazardous voltages capable of causing death or serious personal injury.

Turn off the printer using both Branch Circuit Breakers located in the building's Power Distribution Unit (PDU) before servicing the printer. The printer must be connected to earthed mains outlets only.

To avoid the risk of electric shock, do not attempt the following actions:

Do not attempt to dismantle the drying and curing modules or the electrical control cabinet.

Do not remove or open any other closed system covers or plugs.

Do not insert objects through slots in the printer.

ENWW

General safety guidelines 1

Image 5
Contents HP Designjet L65500 Printer & HP Scitex LX Printer family Trademarks Table of contents Prepare for printing Configure the electrical systemPurge the ink system Prepare the printer General safety guidelines Safety precautionsHeat hazard Heavy substrate hazard Label Explanation Emergency stop buttons Manpower required Installation guide overviewTools required for installation IntroductionL65500 only Inbox contentEnww Unload the crate Receive the shipmentRemove the crate packaging Move the printer over rampsRemove the printer from the pallet Enww Lift the printer to a second floor using a crane Enww Choose the final position Set up the printer in the final positionHow to push the printer Set up the printer in the final position Remove additional packaging Enww Enww Enww Enww Lower the feet Requirements Connect the power cablesTri-phase AC Power Cord Tri-phase Power Cord attachment Tri-phase AC Power Cord Protective Earth attachment Protective Earth conductors groundingInstall the fuses and power jumper Configure the electrical systemInstall the power jumpers Install the fusesHeating Module Configuration Choose delta or star Y configurationCuring Module Configuration Check connections Check resistancesGround check Connect mains powerPower on the printer Power on the printer Enww Make sure that the printer is ready to be turned on Turn power onConfigure the voltage Purge the ISM tubes Purge the ink systemInk Supply Legend Enww Ink Supply Legend Enww Problems with the ink sensor value Enww Enww Fill the intermediate ink tanks Purge the tubes from the ISM to the printheads Enww Enww Enww Prepare the printer Install the printhead cleaning roll and aerosol filtersInstall the printhead cleaning roll Install the printhead cleaning roll and aerosol filters Install the aerosol filters Manpower Tools Time Person T20, T30 Phillips screwdriver Enww Create a folder called OutJobs Enww Enww Configure the printer’s IP address Prepare for printing Install the printheadsEnww Enww Callme@HP Setup Process Antivirus Registration Web Cam InstallationLoad a substrate Connect the air supplyCustomers RIP for use with the HP Designjet L65500 Printer Configure the RIPHP Scitex Onyx RIP HP Scitex Caldera RIP Install the coversInstall the covers Print the HP test images Print the HP test images Prepare the HP Internal Print Server Japan and Russia only Update the rate indexChange the power settings Enww Set a blank screen saver Configure the hard diskEnable scheduled defragmentation Configure the proxy Configure visual effectsInstall the HP Internal Print Server Enww Manually configure the printer’s IP address Select IPV4 Settings Select Config Method Enww Change the Windows Vista language Enww
Related manuals
Manual 16 pages 36.28 Kb