HP Scitex LX800 Industrial manual Install the fuses, Install the power jumpers

Page 32

Install the fuses

1.Use the key to access the electrical cabinet.

2.Open the two fuse holder blocks.

3.Insert the six fuses (three per fuse block) into the fuse holder with the piston facing you.

Printer

Sites with high voltage supply (200–

 

290V)

Sites with low voltage supply (100– 120)

HP Designjet L65500/LX600

20 A

32 A

 

 

 

HP Designjet LX800

25 A

40 A

1Japan may have input frequencies of 50 Hz or 60 Hz

4.Close the fuse holder until you feel and hear a “click.” The red square above the fuse holder should change color once all fuse holders have been inserted.

Install the power jumpers

1.There are five power jumpers supplied. Select the appropriate power jumper according to the single-phase power at the installation site. Inserting the wrong power jumper will cause the vacuum pump to work incorrectly.

2.Insert the correct power jumper into the connector, located close to the transformer.

28 Chapter 6 Configure the electrical system

ENWW

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HP Designjet L65500 Printer & HP Scitex LX Printer family Trademarks Table of contents Prepare for printing Configure the electrical systemPurge the ink system Prepare the printer Safety precautions General safety guidelinesHeat hazard Heavy substrate hazard Label Explanation Emergency stop buttons Installation guide overview Manpower requiredTools required for installation IntroductionInbox content L65500 onlyEnww Receive the shipment Unload the crateMove the printer over ramps Remove the crate packagingRemove the printer from the pallet Enww Lift the printer to a second floor using a crane Enww Choose the final position Set up the printer in the final positionHow to push the printer Set up the printer in the final position Remove additional packaging Enww Enww Enww Enww Lower the feet Requirements Connect the power cablesTri-phase AC Power Cord Tri-phase Power Cord attachment Tri-phase AC Power Cord Protective Earth conductors grounding Protective Earth attachmentConfigure the electrical system Install the fuses and power jumperInstall the fuses Install the power jumpersChoose delta or star Y configuration Heating Module ConfigurationCuring Module Configuration Check resistances Check connectionsGround check Connect mains powerPower on the printer Power on the printer Enww Turn power on Make sure that the printer is ready to be turned onConfigure the voltage Purge the ink system Purge the ISM tubesInk Supply Legend Enww Ink Supply Legend Enww Problems with the ink sensor value Enww Enww Fill the intermediate ink tanks Purge the tubes from the ISM to the printheads Enww Enww Enww Prepare the printer Install the printhead cleaning roll and aerosol filtersInstall the printhead cleaning roll Install the printhead cleaning roll and aerosol filters Install the aerosol filters Manpower Tools Time Person T20, T30 Phillips screwdriver Enww Create a folder called OutJobs Enww Enww Configure the printer’s IP address Install the printheads Prepare for printingEnww Enww Callme@HP Setup Process Web Cam Installation Antivirus RegistrationLoad a substrate Connect the air supplyConfigure the RIP Customers RIP for use with the HP Designjet L65500 PrinterHP Scitex Onyx RIP Install the covers HP Scitex Caldera RIPInstall the covers Print the HP test images Print the HP test images Update the rate index Prepare the HP Internal Print Server Japan and Russia onlyChange the power settings Enww Configure the hard disk Set a blank screen saverEnable scheduled defragmentation Configure visual effects Configure the proxyInstall the HP Internal Print Server Enww Manually configure the printer’s IP address Select IPV4 Settings Select Config Method Enww Change the Windows Vista language Enww
Related manuals
Manual 16 pages 36.28 Kb
Top Page Image Contents