HP Scitex LX800 Industrial manual Introduction, Installation guide overview, Manpower required

Page 10

2 Introduction

Installation guide overview

This installation guide provides you with step by step procedures for the installation process. This guide is organized in chronological order and should be followed from beginning to end.

Manpower required

Installation of your HP Designjet L65500 & HP Scitex LX600/LX800 requires the following manpower:

●HP Installation Specialist

●Customer

●Certified electrician

●Moving specialist

Tools required for installation

TIP: Without a heavy-duty electric screwdriver, it could take up to two hours just to disassemble the crate.

Installation of your HP Designjet L65500 HP Scitex LX600/LX800 requires the following tools:

●Step ladder

●Cutting pliers

●Cutter

●Heavy-duty electric screwdriver with two batteries

●Phillips screwdrivers

●T8, T10, T15, T20, T25 and T30 torx screwdrivers

●Long torx extension pins that have a diameter of approximately 2–3 mm and are more than 15 cm in length to be able to access all screws

●Two Flathead screwdrivers (two sizes)

●Socket wrench, extension and 17 mm socket

●7 mm, 15 mm and two 30 mm open-end wrenches

6 Chapter 2 Introduction

ENWW

Image 10

Contents HP Designjet L65500 Printer & HP Scitex LX Printer family Trademarks Table of contents Purge the ink system Prepare the printer Configure the electrical systemPrepare for printing Safety precautions General safety guidelinesHeat hazard Heavy substrate hazard Label Explanation Emergency stop buttons Tools required for installation Installation guide overviewManpower required IntroductionInbox content L65500 onlyEnww Receive the shipment Unload the crateMove the printer over ramps Remove the crate packagingRemove the printer from the pallet Enww Lift the printer to a second floor using a crane Enww How to push the printer Set up the printer in the final positionChoose the final position Set up the printer in the final position Remove additional packaging Enww Enww Enww Enww Lower the feet Tri-phase AC Power Cord Connect the power cablesRequirements Tri-phase Power Cord attachment Tri-phase AC Power Cord Protective Earth conductors grounding Protective Earth attachmentConfigure the electrical system Install the fuses and power jumperInstall the fuses Install the power jumpersChoose delta or star Y configuration Heating Module ConfigurationCuring Module Configuration Check resistances Check connectionsPower on the printer Connect mains powerGround check Power on the printer Enww Turn power on Make sure that the printer is ready to be turned onConfigure the voltage Purge the ink system Purge the ISM tubesInk Supply Legend Enww Ink Supply Legend Enww Problems with the ink sensor value Enww Enww Fill the intermediate ink tanks Purge the tubes from the ISM to the printheads Enww Enww Enww Install the printhead cleaning roll Install the printhead cleaning roll and aerosol filtersPrepare the printer Install the printhead cleaning roll and aerosol filters Install the aerosol filters Manpower Tools Time Person T20, T30 Phillips screwdriver Enww Create a folder called OutJobs Enww Enww Configure the printer’s IP address Install the printheads Prepare for printingEnww Enww Callme@HP Setup Process Load a substrate Web Cam InstallationAntivirus Registration Connect the air supplyConfigure the RIP Customers RIP for use with the HP Designjet L65500 PrinterHP Scitex Onyx RIP Install the covers HP Scitex Caldera RIPInstall the covers Print the HP test images Print the HP test images Update the rate index Prepare the HP Internal Print Server Japan and Russia onlyChange the power settings Enww Configure the hard disk Set a blank screen saverEnable scheduled defragmentation Configure visual effects Configure the proxyInstall the HP Internal Print Server Enww Manually configure the printer’s IP address Select IPV4 Settings Select Config Method Enww Change the Windows Vista language Enww

Related manuals

Manual 16 pages 36.28 Kb