Sterling SDA 1000-5100 specifications Entering Operating Parameters to Select Modes, On, Off

Page 31

Entering Operating Parameters to Select Modes

To enter the display:

1.Press the Mode Display key to view the Run/Stop & Alarm 1 Modes.

2.Press and to set the higher or lower the values of the parameter or turn that function On or Off.

The SV readout displays the different values for the parameter within a mode.

3.To switch modes within a level, press and hold the Level Display key for one (1) second.

The PV readout will display the different parameters within each mode.

4.Use short presses on the Mode Display key to display each parameter within a mode.

The SV readout displays the different values for the parameter within a mode.

5.Press and to set the higher or lower the values of a parameter or turn that function On or Off.

6.Press Level Key once to return to the Process Temperature Setting.

Figure 12: Settings for Process Temperature Controller (E5CN), Part No. A0555757

Mode

Parameter

Setting range

Default

Manuf. setting

Operation

Run/Stop

Run/Stop

Run

-

Alarm value 1

-1999 to 9999

0

25

 

Mode

Parameter

Setting range

Default

Manuf. setting

 

AT execute/cancel

ON, OFF

OFF

?

Adjustment

Temperature input shift

-199.9 to 999.9

0.0

-

Proportional Band

0.1 to 999.9

8.0

?

 

Integral Time

0 to 3999

233

?

 

Derivative Time

0 to 3999

40

?

Large Dehumidifying Dryers

Controls

31

Image 31
Contents SDA Large Dehumidifying Dryers With AP0 Controls If the Shipment is Not Complete Shipping InfoUnpacking and Inspection Event of Shipping DamageReturns Warranty ReturnsCredit Returns Table of Contents Operation Dryer Identification Serial Number Tag Technical Assistance How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves Dryer Safety Tags DescriptionGeneral Responsibility ResponsibilityOperator Responsibility Maintenance Responsibility Reporting a Safety Defect Models Covered in This Manual Functional DescriptionGeneral Description Regeneration Cycle Process/Regeneration CycleSequence of Operation Controller Screen Descriptions Controller DescriptionMechanical Features Standard FeaturesElectrical Features Closed-Loop Regeneration OptionsProcess Aftercooler Process Air Dust Collector Recommended Temperature SettingsMaterial Overdrying Protection Electrical Options Mechanical OptionsFail Safe Operation Safety Devices and InterlocksSafety Circuit Standards Safety Device Lock-OutsPage Making Electrical Connections Mechanical InstallationUncrating the Equipment Rigging and Placing UnitChecking Blower Rotation Checking for Proper Blower RotationDryer/Drying Hopper Process Air Connections Making Dryer/Drying Hopper Process Air ConnectionsAftercooler Components & Flow Rates Connecting Aftercooler/Precooler Cooling Water OptionalDrying Hopper Air Trap Using the Drying Hopper Air TrapControls SwitchesIndicator Lights Process Air Temperature ControllerLights in the Operation Indicator Section when Lit when Control Output 1 is on. The Out1Lit when Control Output 2 is on. Not used Indicator Name DescriptionE5CN Operating Parameters Setting the Process Air TemperatureTuned prior to dryer startup Adjustment Level Indicator Name DescriptionON, OFF Entering Operating Parameters to Select ModesProcess Air Dew Point Display Setting the High Dew Point AlarmOptional Setting the Redundant Safety Controller Redundant Safety Controller DisplayWatlow Operating Parameters Manf. setting Pre-Startup Checks Auto-Tuning the DryerOperation Initial Start-upDryer Operation Procedures Page Material Miser OFF Press + to Enable Alarm Display Messages Shutting Down the Dryer Auto-Tuning the DryerMaintenance Schedule MaintenancePhotocopy this page for your maintenance records Cleaning or Replacing the Process Air Filters Preventative MaintenanceCalibrating the Dirty Filter Alarm Cleaning or Replacing the Regeneration FilterChecking the Dewpoint Control System Symptoms of Worn Out Desiccant Corrective MaintenanceReplacing the Desiccant Replacing the Process Heater Electric Dryers Desiccant Tower AssemblyReplacing the Regeneration Heater Electric Dryers Process Heater Box AssemblyRegeneration Heater Box Assembly Basic Troubleshooting TroubleshootingIntroduction Large Dehumidifying Dryers Troubleshooting Alarm Descriptions AlarmsAlarm Alarm Description Alarm Effect Code Using a Thermocouple Determining Temperature Controller Errors or Sensor ErrorsUsing a Platinum Resistance Thermometer Appendix WarrantyAftercooler Design Specifications Technical SpecificationsAnnex B Information Drawings and Diagrams Optional dryer dust collector Spare Parts List Level 3 Mechanical Components Located on back of Dryer Dryer Identification Serial Number TagParts and Service Department Sales Department Service DepartmentTechnical Assistance Parts Department