Sterling SDA 1000-5100 specifications Material Miser OFF Press + to Enable

Page 38

on the relay screen. Press ALARM RESET to deactivate the alarm until the next dew point fault occurs.

15.Use the right arrow key to display the REGEN SET screen (Screen 1). Use the up & down arrow keys to select the parameter to change. Use the + & - keys to change the parameter value. Press the OK key to accept and store the changed values. Press ESC to cancel changes.

REGEN

SET

HEAT 45

COOL 20

Screen 1.

16.Use the right arrow key to display the Material Miser screen. Use the + key to enable/ disable this feature. See Screens 2 & 3.

MATERIAL

MISER OFF

PRESS + TO

ENABLE

Screen 2.

MTL MISER ON

+TO DISABLE MM IS :

NOT ACTIVE

Screen 3.

17.Use the right arrow key to display the Closed Loop Regen screen. Use the + key to enable / disable this feature. See Screens 4 & 5.

CLOSED LOOP

REGEN OFF

PRESS + TO

ENABLE

Screen 4.

CL REGEN ON

+TO DISABLE CL IS :

NOT ACTIVE

Screen 5.

Large Dehumidifying Dryers

Operation

38

Image 38

Contents SDA Large Dehumidifying Dryers With AP0 Controls Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not CompleteCredit Returns Warranty ReturnsReturns Table of Contents Operation Dryer Identification Serial Number Tag Technical Assistance Safety Symbols Used in this Manual SafetyHow to Use This Manual Dryer Safety Tags Description Wear Safety Glasses and Work GlovesOperator Responsibility ResponsibilityGeneral Responsibility Maintenance Responsibility Reporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Process/Regeneration Cycle Regeneration CycleSequence of Operation Controller Description Controller Screen DescriptionsElectrical Features Standard FeaturesMechanical Features Process Aftercooler OptionsClosed-Loop Regeneration Material Overdrying Protection Recommended Temperature SettingsProcess Air Dust Collector Mechanical Options Electrical OptionsSafety Device Lock-Outs Safety Devices and InterlocksSafety Circuit Standards Fail Safe OperationPage Rigging and Placing Unit Mechanical InstallationUncrating the Equipment Making Electrical ConnectionsChecking for Proper Blower Rotation Checking Blower RotationMaking Dryer/Drying Hopper Process Air Connections Dryer/Drying Hopper Process Air ConnectionsConnecting Aftercooler/Precooler Cooling Water Optional Aftercooler Components & Flow RatesUsing the Drying Hopper Air Trap Drying Hopper Air TrapProcess Air Temperature Controller SwitchesIndicator Lights ControlsIndicator Name Description Lit when Control Output 1 is on. The Out1Lit when Control Output 2 is on. Not used Lights in the Operation Indicator Section whenSetting the Process Air Temperature E5CN Operating ParametersAdjustment Level Indicator Name Description Tuned prior to dryer startupEntering Operating Parameters to Select Modes ON, OFFOptional Setting the High Dew Point AlarmProcess Air Dew Point Display Watlow Operating Parameters Redundant Safety Controller DisplaySetting the Redundant Safety Controller Manf. setting Initial Start-up Auto-Tuning the DryerOperation Pre-Startup ChecksDryer Operation Procedures Page Material Miser OFF Press + to Enable Alarm Display Messages Auto-Tuning the Dryer Shutting Down the DryerPhotocopy this page for your maintenance records MaintenanceMaintenance Schedule Preventative Maintenance Cleaning or Replacing the Process Air FiltersCleaning or Replacing the Regeneration Filter Calibrating the Dirty Filter AlarmChecking the Dewpoint Control System Replacing the Desiccant Corrective MaintenanceSymptoms of Worn Out Desiccant Desiccant Tower Assembly Replacing the Process Heater Electric DryersProcess Heater Box Assembly Replacing the Regeneration Heater Electric DryersRegeneration Heater Box Assembly Introduction TroubleshootingBasic Troubleshooting Large Dehumidifying Dryers Troubleshooting Alarm Alarm Description Alarm Effect Code AlarmsAlarm Descriptions Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Warranty AppendixAnnex B Information Technical SpecificationsAftercooler Design Specifications Drawings and Diagrams Optional dryer dust collector Spare Parts List Level 3 Mechanical Components Dryer Identification Serial Number Tag Located on back of DryerParts and Service Department Parts Department Service DepartmentTechnical Assistance Sales Department