Sterling SDA 1000-5100 specifications Manf. setting

Page 34

Entering Operating Parameters to Select Modes

To enter the display:

1.Press both the Up and Down keys for three seconds from the home page. The word SEE will appear in the upper display and PAGE will appear in the lower display.

2.Press the Advance Key to move through the parameter prompts.

3.Press the Up or Down keys to change the parameter value.

4.Press the RESET Key at any time to return to the Home Page display.

Figure 15: Setting List for Redundant Safety Controller (WATLOW), Part No. A0555757

	Mode	Parameter	Setting range	Default	Manf. setting
	SEn	Sensor Type	0-3	0	-
	Lin	Thermocouple Linearization	0-10	0	H (1)
	C-F	Temperature Units	Fahrenheit / Celsius	F	-
	S.dEC	Temp. Decimal Places	0 – 0.0	0	-
	IS.En	INFOSENSE™	Yes / No	No	-
	Sc.Lo	Process Scale Low	4.00 to 20.00 mA	4.00 mA	0
			1.00 to 10.00V	1.00V
	Sc.hi	Process Scale High	4.00 to 20.00 mA	20.00 mA	400
			1.00 to 10.00V	5.00 V
	CAL	Calibration Offset	-999 to 999	0	-
	Ftr.E	Input Filter	Off, DiSP, Cont, both	OFF	-
	Ot 1	Output 1 Function	Limit (2)	(2)	-
	LSd1	Output 1 Limit Sides	Both, High, Low	Both	High
	hyS1	Limit 1 Hysteresis	0.0 to 999.0	1.0	-
	Ot2	Output 2 Function	Off / Process Alarm / Limit (2)	OFF	-
	LSd2	Output 2 Sides	Both / high / low	Both	-
			None, Process Value, Limit 1 Low Set,
			Limit 1 High Set, Limit 2 Low Set, Limit
	UdSP	Upper Display Look	2 High Set, Alarm 2 Low Set, Alarm 2	Process	-
			High Set, Limit 3 Low Set, Limit 3 High
			Set, Alarm 3 Low Set, Alarm 3 High Set
			None, Process Value, Limit 1 Low Set,
			Limit 1 High Set, Limit 2 Low Set, Limit	Limit 1
	LdSP	Lower Display Look	2 High Set, Alarm 2 Low Set, Alarm 2	Limit 1	-
	LdSP	Lower Display Look	2 High Set, Alarm 2 Low Set, Alarm 2	High Set	-
			High Set, Limit 3 Low Set, Limit 3 High	High Set
			High Set, Limit 3 Low Set, Limit 3 High
			Set, Alarm 3 Low Set, Alarm 3 High Set
			(0) no lockout, (1) Programming and
			Setup Page Locked, (2) Limit Set
	LOC	Lockout	Points are the only Operation Page	0	2
			parameters accessible, (3) Full
			Lockout.

Large Dehumidifying Dryers

Controls

34

Image 34

Contents SDA Large Dehumidifying Dryers With AP0 Controls Event of Shipping Damage Shipping InfoUnpacking and Inspection If the Shipment is Not CompleteReturns Warranty ReturnsCredit Returns Table of Contents Operation Dryer Identification Serial Number Tag Technical Assistance How to Use This Manual SafetySafety Symbols Used in this Manual Dryer Safety Tags Description Wear Safety Glasses and Work GlovesGeneral Responsibility ResponsibilityOperator Responsibility Maintenance Responsibility Reporting a Safety Defect Models Covered in This Manual Functional DescriptionGeneral Description Process/Regeneration Cycle Regeneration CycleSequence of Operation Controller Description Controller Screen DescriptionsMechanical Features Standard FeaturesElectrical Features Closed-Loop Regeneration OptionsProcess Aftercooler Process Air Dust Collector Recommended Temperature SettingsMaterial Overdrying Protection Mechanical Options Electrical OptionsSafety Device Lock-Outs Safety Devices and InterlocksSafety Circuit Standards Fail Safe OperationPage Rigging and Placing Unit Mechanical InstallationUncrating the Equipment Making Electrical ConnectionsChecking for Proper Blower Rotation Checking Blower RotationMaking Dryer/Drying Hopper Process Air Connections Dryer/Drying Hopper Process Air ConnectionsConnecting Aftercooler/Precooler Cooling Water Optional Aftercooler Components & Flow RatesUsing the Drying Hopper Air Trap Drying Hopper Air TrapProcess Air Temperature Controller SwitchesIndicator Lights ControlsIndicator Name Description Lit when Control Output 1 is on. The Out1Lit when Control Output 2 is on. Not used Lights in the Operation Indicator Section whenSetting the Process Air Temperature E5CN Operating ParametersAdjustment Level Indicator Name Description Tuned prior to dryer startupEntering Operating Parameters to Select Modes ON, OFFProcess Air Dew Point Display Setting the High Dew Point AlarmOptional Setting the Redundant Safety Controller Redundant Safety Controller DisplayWatlow Operating Parameters Manf. setting Initial Start-up Auto-Tuning the DryerOperation Pre-Startup ChecksDryer Operation Procedures Page Material Miser OFF Press + to Enable Alarm Display Messages Auto-Tuning the Dryer Shutting Down the DryerMaintenance Schedule MaintenancePhotocopy this page for your maintenance records Preventative Maintenance Cleaning or Replacing the Process Air FiltersCleaning or Replacing the Regeneration Filter Calibrating the Dirty Filter AlarmChecking the Dewpoint Control System Symptoms of Worn Out Desiccant Corrective MaintenanceReplacing the Desiccant Desiccant Tower Assembly Replacing the Process Heater Electric DryersProcess Heater Box Assembly Replacing the Regeneration Heater Electric DryersRegeneration Heater Box Assembly Basic Troubleshooting TroubleshootingIntroduction Large Dehumidifying Dryers Troubleshooting Alarm Descriptions AlarmsAlarm Alarm Description Alarm Effect Code Using a Thermocouple Determining Temperature Controller Errors or Sensor ErrorsUsing a Platinum Resistance Thermometer Warranty AppendixAftercooler Design Specifications Technical SpecificationsAnnex B Information Drawings and Diagrams Optional dryer dust collector Spare Parts List Level 3 Mechanical Components Dryer Identification Serial Number Tag Located on back of DryerParts and Service Department Parts Department Service DepartmentTechnical Assistance Sales Department