Sterling SDAA 25-100 Electrical Connections, Suggested Lift Rigging for Machine Mounted Dryers

Page 20

Figure 3: Suggested Lift Rigging for Machine Mounted Dryers

Caution! When using a hoist to move a machine mounted dryer, ALWAYS attach chains to the three (3) locations/lifting points on the unit! Moving the Dryer without the chains attached to all of the lifting points will cause the unit to become unstable and may cause damage to the Dryer and/or injury to personnel!

3-3 Electrical Connections

When making electrical connections to your dryer, ensure that you take into consideration and make arrangements for the following:

•A qualified electrician should make all electrical connections.

•Fulfill all national, state, and local safety and electrical code requirements.

•The serial tag lists voltage, phase, and amp draw information:

•Line voltage must be within plus or minus ten percent (±10%) of the voltage listed on the serial tag, or damage may occur. Phase imbalance must be less than two percent (2%).

•Connect main power to the dryer at the disconnect or terminals in the upper right corner of the control enclosure.

•Install a fused disconnect with a lockout feature in the power main leading to the dryer.

•The power drop must include a ground wire.

•Make sure all electrical connections are tight.

Dehumidifying Dryers

Chapter 3: Installation

19 of 59

Image 20

Contents Sdaa 25-100 15-60 cfm Dehumidifying Dryers Shipping Information Table of Contents Maintenance Service Department Sales Department Contract Department Safety Symbols Used in this Manual SafetyHow to Use This Manual Wear Safety Glasses and Work Gloves Responsibility General ResponsibilityOperator Responsibility RememberMaintenance Responsibility Reporting a Safety DefectDehumidifying Dryers Safety General Description Functional DescriptionModels Covered in This Manual Standard Features What is desiccant?Mechanical Features Electrical FeaturesOptions Safety Devices and InterlocksController Features Fail Safe Operation Safety Circuit StandardsSafety Device Lock-Outs Rigging and Placing the Dryer InstallationUncrating the Equipment Machine-Mount Dryer Dimensions Floor-Mount Dryer Dimensions Suggested Lift Rigging for Cart Mounted Dryers Recommended Dryer Lifting HardwareElectrical Connections Suggested Lift Rigging for Machine Mounted DryersSetup Procedures Three-Phase ModelsChecking for Proper Blower Rotation Making Dryer/Drying Hopper Process Air ConnectionsOptional Aftercooler Installing Water Lines Hose and Hose ClampDrying Hopper Air Trap Considerations Auto-Tuning the Dryer Initial Start-upPre-Startup Checks Starting Up the DryerShutting Down the Dryer Operation Start-upController Description and Operation SwitchesIndicator Lights Lit when Control Output 2 is on. Not used Process Air Temperature ControllerLit when Control Output 1 is on. The Out1 Indicator Name Description Lights in the Operation Indicator Section whenIdentifying Temperature Controller Keys Setting the Process Air TemperatureE5CN Operating Parameters Adjustment Level Indicator Name Description Tuned prior to dryer startupEntering Operating Parameters to Select Modes ON, OFFOptional Setting the High Dew Point AlarmProcess Air Dew Point Display Watlow Operating Parameters Redundant Safety Controller DisplaySetting the Redundant Safety Controller Mode Parameter Setting range Default Manf. setting Dryer Operation Procedures Model Heating Cooling 15 cfm 30 cfm 60 cfm Page Controller Operation With Optional Alarm Horn & Reset Button Page Alarm Display Messages Auto-Tuning the Dryer Shutting Down the DryerPhotocopy this page for your maintenance records MaintenancePreventative Maintenance Schedule Preventative Maintenance Recommendations for Cleaning and Replacing FiltersServicing Process Air Filters VacuumingCleaning with Compressed Air Servicing the Dew Point MonitorCorrective Maintenance Symptoms of Worn DesiccantFirst AID Replacing Worn DesiccantConsult local disposal regulations for more information Procedures Replacing the Process HeaterIntroduction TroubleshootingProblem Possible cause Corrective action Problem Possible cause Corrective action Check resin manufacturer’s data Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Warranty Warranty SpecificationsWarranty Restrictions AppendixCustomer Responsibilities Warranty LiabilitiesOptional Components Technical Specifications Annex B InformationDrawings and Diagrams Spare Parts List Aftercooler Design SpecificationsLevel 2 & 3 Spare Parts List Electrical & Mechanical Safety Tag Information Warranty ReturnsDryer Safety Tags Returned Material PolicyDryer Identification Serial Number Tag Located on back of DryerService Department Technical AssistanceParts Department Sales Department