Sterling SDAA 25-100 specifications Operator Responsibility, Remember

Page 9

Operator Responsibility

The operator’s responsibility does not end with efficient production. The operator usually has the most daily contact with the equipment and intimately knows its capabilities and limitations.

Plant and personnel safety is sometimes forgotten in the desire to meet incentive rates, or through a casual attitude toward machinery formed over a period of months or years. Your employer probably has established a set of safety rules in your workplace. Those rules, this manual, or any other safety information will not keep you from being injured while operating your equipment.

Learn and always use safe operation. Cooperate with co-workers to promote safe practices. Immediately report any potentially dangerous situation to your supervisor or appropriate person.

REMEMBER:

•NEVER place your hands or any part of your body in any dangerous location.

•NEVER operate, service, or adjust the dryer without appropriate training and first reading and understanding this manual.

•NEVER try to pull material out of the dryer with your hands while it is running!

•Before you start the dryer check the following:

•Remove all tools from the dryer;

•Be sure no objects (tools, nuts, bolts, clamps, bars) are laying in the hopper area;

•If your dryer has been inoperative or unattended, check all settings before starting the unit.

•At the beginning of your shift and after breaks, verify that the controls and other auxiliary equipment are functioning properly.

•Keep all safety guards in place and in good repair. NEVER attempt to bypass, modify, or remove safety guards. Such alteration is not only unsafe, but will void the warranty on your equipment.

•When changing control settings to perform a different mode of operation, be sure selector switches are correctly positioned. Locking selector switches should only be adjusted by authorized personnel and the keys removed after setting.

•Report the following occurrences IMMEDIATELY:

•unsafe operation or condition

•unusual dryer action

•leakage

•improper maintenance

•NEVER stand or sit where you could slip or stumble into the dryer while working on it.

•DO NOT wear loose clothing or jewelry, which can be caught while working on a dryer. In addition, cover or tie back long hair.

Dehumidifying Dryers

Chapter 1: Safety

viii

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Sdaa 25-100 15-60 cfm Dehumidifying Dryers Shipping Information Table of Contents Maintenance Service Department Sales Department Contract Department Safety How to Use This ManualSafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityDehumidifying Dryers Safety Functional Description Models Covered in This ManualGeneral Description What is desiccant? Standard FeaturesMechanical Features Electrical FeaturesSafety Devices and Interlocks Controller FeaturesOptions Safety Circuit Standards Safety Device Lock-OutsFail Safe Operation Installation Uncrating the EquipmentRigging and Placing the Dryer Machine-Mount Dryer Dimensions Floor-Mount Dryer Dimensions Recommended Dryer Lifting Hardware Suggested Lift Rigging for Cart Mounted DryersSuggested Lift Rigging for Machine Mounted Dryers Electrical ConnectionsThree-Phase Models Setup ProceduresChecking for Proper Blower Rotation Making Dryer/Drying Hopper Process Air ConnectionsInstalling Water Lines Hose and Hose Clamp Drying Hopper Air Trap ConsiderationsOptional Aftercooler Initial Start-up Auto-Tuning the DryerPre-Startup Checks Starting Up the DryerShutting Down the Dryer Start-up OperationSwitches Indicator LightsController Description and Operation Process Air Temperature Controller Lit when Control Output 1 is on. The Out1Lit when Control Output 2 is on. Not used Lights in the Operation Indicator Section when Indicator Name DescriptionIdentifying Temperature Controller Keys Setting the Process Air TemperatureE5CN Operating Parameters Tuned prior to dryer startup Adjustment Level Indicator Name DescriptionON, OFF Entering Operating Parameters to Select ModesSetting the High Dew Point Alarm Process Air Dew Point DisplayOptional Redundant Safety Controller Display Setting the Redundant Safety ControllerWatlow Operating Parameters Mode Parameter Setting range Default Manf. setting Dryer Operation Procedures Model Heating Cooling 15 cfm 30 cfm 60 cfm Page Controller Operation With Optional Alarm Horn & Reset Button Page Alarm Display Messages Shutting Down the Dryer Auto-Tuning the DryerMaintenance Preventative Maintenance SchedulePhotocopy this page for your maintenance records Recommendations for Cleaning and Replacing Filters Preventative MaintenanceServicing Process Air Filters VacuumingServicing the Dew Point Monitor Cleaning with Compressed AirSymptoms of Worn Desiccant Corrective MaintenanceReplacing Worn Desiccant First AIDConsult local disposal regulations for more information Replacing the Process Heater ProceduresTroubleshooting Problem Possible cause Corrective actionIntroduction Problem Possible cause Corrective action Check resin manufacturer’s data Determining Temperature Controller Errors or Sensor Errors Using a ThermocoupleUsing a Platinum Resistance Thermometer Warranty Specifications WarrantyWarranty Restrictions AppendixWarranty Liabilities Optional ComponentsCustomer Responsibilities Annex B Information Technical SpecificationsAftercooler Design Specifications Drawings and Diagrams Spare Parts ListLevel 2 & 3 Spare Parts List Electrical & Mechanical Warranty Returns Safety Tag InformationDryer Safety Tags Returned Material PolicyLocated on back of Dryer Dryer Identification Serial Number TagTechnical Assistance Service DepartmentParts Department Sales Department
Top Page Image Contents