Sterling SDAA 25-100 specifications Entering Operating Parameters to Select Modes, On, Off

Page 31

Entering Operating Parameters to Select Modes

To enter the display:

1.Press the Mode Display key to view the Run/Stop & Alarm 1 Modes.

2.Press and to set the higher or lower the values of the parameter or turn that function On or Off.

The SV readout displays the different values for the parameter within a mode.

3.To switch modes within a level, press and hold the Level Display key for one

(1) second.

The PV readout will display the different parameters within each mode.

4.Use short presses on the Mode Display key to display each parameter within a mode.

The SV readout displays the different values for the parameter within a mode.

5.Press and to set the higher or lower the values of a parameter or turn that function On or Off.

6.Press Level Key once to return to the Process Temperature Setting.

Figure 6: Settings for Process Temperature Controller (E5CN), Part No. A0555757

	Mode	Parameter	Setting range	Default	Manuf. setting
	Operation	Run/Stop	Run/Stop	Run	-
	Operation	Alarm value 1	-1999 to 9999	0	25
		Alarm value 1	-1999 to 9999	0	25

Mode	Parameter	Setting range	Default	Manuf. setting
	AT execute/cancel	ON, OFF	OFF	?
Adjustment	Temperature input shift	-199.9 to 999.9	0.0	-
Adjustment	Proportional Band	0.1 to 999.9	8.0	?
	Integral Time	0 to 3999	233	?
	Derivative Time	0 to 3999	40	?

Dehumidifying Dryers

Chapter 4: Operation

30 of 59

Image 31

Contents Sdaa 25-100 15-60 cfm Dehumidifying Dryers Shipping Information Table of Contents Maintenance Service Department Sales Department Contract Department How to Use This Manual SafetySafety Symbols Used in this Manual Wear Safety Glasses and Work Gloves General Responsibility ResponsibilityRemember Operator ResponsibilityReporting a Safety Defect Maintenance ResponsibilityDehumidifying Dryers Safety Models Covered in This Manual Functional DescriptionGeneral Description Electrical Features Standard FeaturesWhat is desiccant? Mechanical FeaturesController Features Safety Devices and InterlocksOptions Safety Device Lock-Outs Safety Circuit StandardsFail Safe Operation Uncrating the Equipment InstallationRigging and Placing the Dryer Machine-Mount Dryer Dimensions Floor-Mount Dryer Dimensions Recommended Dryer Lifting Hardware Suggested Lift Rigging for Cart Mounted DryersSuggested Lift Rigging for Machine Mounted Dryers Electrical ConnectionsMaking Dryer/Drying Hopper Process Air Connections Setup ProceduresThree-Phase Models Checking for Proper Blower RotationDrying Hopper Air Trap Considerations Installing Water Lines Hose and Hose ClampOptional Aftercooler Starting Up the Dryer Auto-Tuning the DryerInitial Start-up Pre-Startup ChecksShutting Down the Dryer Start-up OperationIndicator Lights SwitchesController Description and Operation Lit when Control Output 1 is on. The Out1 Process Air Temperature ControllerLit when Control Output 2 is on. Not used Setting the Process Air Temperature Indicator Name DescriptionLights in the Operation Indicator Section when Identifying Temperature Controller KeysE5CN Operating Parameters Tuned prior to dryer startup Adjustment Level Indicator Name DescriptionON, OFF Entering Operating Parameters to Select ModesProcess Air Dew Point Display Setting the High Dew Point AlarmOptional Setting the Redundant Safety Controller Redundant Safety Controller DisplayWatlow Operating Parameters Mode Parameter Setting range Default Manf. setting Dryer Operation Procedures Model Heating Cooling 15 cfm 30 cfm 60 cfm Page Controller Operation With Optional Alarm Horn & Reset Button Page Alarm Display Messages Shutting Down the Dryer Auto-Tuning the DryerPreventative Maintenance Schedule MaintenancePhotocopy this page for your maintenance records Vacuuming Preventative MaintenanceRecommendations for Cleaning and Replacing Filters Servicing Process Air FiltersServicing the Dew Point Monitor Cleaning with Compressed AirSymptoms of Worn Desiccant Corrective MaintenanceReplacing Worn Desiccant First AIDConsult local disposal regulations for more information Replacing the Process Heater ProceduresProblem Possible cause Corrective action TroubleshootingIntroduction Problem Possible cause Corrective action Check resin manufacturer’s data Using a Thermocouple Determining Temperature Controller Errors or Sensor ErrorsUsing a Platinum Resistance Thermometer Appendix WarrantyWarranty Specifications Warranty RestrictionsOptional Components Warranty LiabilitiesCustomer Responsibilities Annex B Information Technical SpecificationsAftercooler Design Specifications Drawings and Diagrams Spare Parts ListLevel 2 & 3 Spare Parts List Electrical & Mechanical Returned Material Policy Safety Tag InformationWarranty Returns Dryer Safety TagsLocated on back of Dryer Dryer Identification Serial Number TagSales Department Service DepartmentTechnical Assistance Parts Department