HP 83236B S Interface manual Qpsk

Page 88

Index

Q	R	S
QPSK	receiver performance in additive noise,	Saving Configuration Information, 54
definition, 80	42	search for PN offset, 44
quadrature phase shift keying	receiver sensitivity, 40	selecting a PCS Band, 51
definition, 80	receiver tests	sensitivity, receiver, 40
quadrature spreading	suspect measurement results, 74	setting up the software, 18
definition, 80	reference signal	Show Instrument Front Panel Connec-
questionable measurement results, 73	definition, 80	tions, 58
	references	Show Instrument Rear Panel Connec-
	connections, 60	tions, 58
	registers	software
	clearing, 65	configuring, 18
	required equipment, 13	definition, 12
	reverse CDMA channel	errors, 65
	definition, 80	loading, 15, 65
	reverse link	navigation, 17
	definition, 80	running, 15, 65
	reverse traffic channel	software definition, 12
	definition, 80	spectrum analyzer, 36
	rho, 28	starting to use the software, 11
	definition, 81	sync channel
	suspect measurement results, 74	definition, 81
	running the software, 15	sync pulse
	runtime errors, 66	definition, 81
	RX Measurement Path Loss, 53	System
		definition, 81
		system configuration errors, 66, 67
		system time
		definition, 81

88

Image 88

Contents CDMA/PCS Base Station Test Software, User’s Guide Restricted Operating Overview Conventions Used in this Book Contents Making Measurements Receiver Sensitivity Operating Overview Setting the Test System Beep Glossary Index Getting Started Introduction Required Equipment You must supplySynth REF Load and Run the CDMA/PCS BS Test Software Tests Main Menu screen CDMA/PCS Test Software main menu features Configure the Software Select Configuration Information MenuScroll to and select your band of interest User k1 Perform Cdma Tests ProblemsIf You Had Perform Cdma Tests Making Measurements Making Measurements Overview Transmitter Measurements Receiver Measurements OtherOverview Average PowerRequirements Steps Information Menu under TX Measurement Path LossModulation Quality Rho Measurement not Correlating in , Troubleshooting, on Code Domain Power Menu Code Domain Timing Details on the use of the Code Domain Analyzer screen Code Domain Phase Already selected Transmit Spectrum AnalyzerSteps Go to Spectrum Analyzer @ Present Chan Steps Go to Spectrum Analyzer & Enter Freq Transmit Spectrum Receiver Sensitivity Main menu, enter the Base Station Channel number Error Rate FER is measured at each Eb/No level Receiver Performance in Additive NoiseEb/No Level Search for PN Offset PN Offset not Found Check for a valid clock signal from the base station Check Even-Second ClockCorrelating in , Troubleshooting, on Check Even-Second Clock Operating Overview Information ConfigurationReference Selecting a PCS Band To select a new PCS BandChannel plans for PCS Band selections Compensating for TX and RX Measurement Path Loss You must know the following loss valuesSaving Configuration Information to Memory BeepLoading Configuration Information from Memory Requirements StepsPurging Configuration Information from Memory Using Autostart Autostart FeatureTurning On Turning OffViewing Instrument Connections ConnectionsSetting the Test System Beep To Memory on Cdma Base Station Operating Overview Troubleshooting Troubleshooting Errors When Loading and Running the Software Memory Overflow ErrorsTest System Configuration Errors at Runtime Compensation not performed. Check Duplex OUT cable. Retry? Errors When Loading and Running the Software Errors While Attempting Measurements Cdma Measurement not CorrelatingErrors While Attempting Measurements Frame Error Rate Receiver Measurements Incorrect Base Station Channel entryErrors While Attempting Measurements Average Power Questionable Measurement ResultsRho Measurements Code DomainMeasurements Receiver TestsSensitivity tests random data not selected for signal source Questionable Measurement Results Glossary Glossary Modulation Quality See Rho Glossary Glossary Glossary Index Index FER Index Oqpsk PCS Qpsk UCT Walsh chip