HP Client Bridge M111 manual About this guide, Products covered, Important terms, Conventions

Page 12

Introduction

About this guide

About this guide

This guide explains how to install, configure, and operate the M111 Client Bridge.

Products covered

The manual applies to the M111 Client Bridge (J9389A WW, J9523A Japan).

Important terms

The following terms are used in this guide.

Term	Description

MSM AP	Refers to any HP ProCurve Networking MSM3xx or MSM4xx Access
	Point.

Controller	Refers to any HP ProCurve Networking MSM7xx Controller, including
	both Access Controller and Mobility Controller variants.

Conventions

This guide uses specific syntax when directing you to interact with the management tool user interface. Refer to the following image for identification of key user-interface elements and then the table below for example directions:

Example directions in this guide	What to do in the user interface

Select Network > Ports	On the main menu select Network and then
	select Ports on the sub-menu.

For Password specify secret22.	In the Password field enter the text secret22
	exactly as shown.

Warnings and cautions

Do not proceed beyond a WARNING or CAUTION notice until you fully understand the hazardous conditions and have taken appropriate steps.

Warning

Identifies a hazard that can cause physical injury or death.

1-2

Image 12

Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Resetting to factory defaults Regulatory informationViii Introduction About this guide Products coveredImportant terms ConventionsCommands and program listings Example DescriptionKey features Introducing the M111 Client BridgeSafety information Professional Installation RequiredServicing HP ProCurve Networking support Online documentationBefore contacting support Getting started Scenario 1 Connecting wired devices to a wireless network Deploying the M111Overview Configuration procedure Configure your computerConnect to the M111 Passwords Select Network DNSConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage About passwords Management toolStarting the management tool Customizing management tool settings Manager and Operator accountsPasswords Security policies SecurityIP address configuration Web serverAuto-refresh To configure IP addressing Radio configuration Wireless rangeTo configure the radio Wireless modeRestrict channels to Antenna selection Fast roaming threshold Fast roaming delta thresholdScan channel delay Fast scan channel delayFast roaming threshold count Minimum SNR thresholdUsing station profiles to establish a wireless link Advanced wireless settingsTransmit power control RTS thresholdWorking with the M111 To add or edit a station profile GeneralWireless security Wireless protectionKey source EAP methodWorking with the M111 Quality of service Viewing APs in the neighborhoodEncryption type Ap1certificate or ap2certificateConfiguring Quality of Service QoS Access categoryField descriptions QoS settings in a station profile Priority mechanisms802.1p Differentiated Services DiffServ Very-high, high, normal, low priorityDisabled Creating IP QoS profilesTo define an IP QoS profile Upstream DiffServ taggingConnecting serial devices SettingsProfile name Protocol Start port/ End portSerial port connector To connect a serial deviceTransmit timeout Idle timeoutMode Remote IP addressDrop wireless link when port 1 is connected Data bitsParity bit Stop bitsDNS configuration Connection timeTx kbytes Rx kbytesDNS switch on server failure Dynamically assigned DNS serversOverride dynamically assigned DNS servers ServerDNS switch over Enable the Redirect unsupported traffic to optionHandling unsupported traffic To forward unsupported trafficCloning the address of a wired device IP forwardingLimitations Wireless access to the M111 when MAC cloning is active Enabling Ethernet MAC cloningSetting up management traffic interception Management tool TCP portSnmp agent UDP port Select Management SnmpUsing filters to restrict wireless traffic Enable the Wireless traffic filters optionSnmp notifications UDP port Remote log UDP portAssigning a management address To assign a management addressSnmp Attributes V1/v2c communitiesV3 users Managing certificates Notification receivers802.1X Install TLS client certificate PasswordInstall 802.1X certificatesCertificate stores 802.1X Manage TLS client certificates802.1X Trusted CA certificates 802.1X Manage CA certificatesInstalling a new CA certificate Trusted CA certificate storeCA certificate import formats Certificate and private key store END CertificateDefault installed private key/public key certificate chains Specify the Pkcs #12 passwordCertificate usage Changing the certificate assigned to a service About certificate warningsConfiguration file management Manual configuration file managementBackup configuration Reset configuration Restore configurationScheduled operations Software updates Performing an immediate software update Performing a scheduled updateSelect Install Enable Scheduled installWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use Operation Using 5 GHz Channels in the European Community GHz OperationSupported External Antennas 5470Indoor or outdoor use 1000 124, 128, 132, 136 Antenna Band GHzDGT LPD Low Power Device Statement Resetting to factory defaults Using the Reset button Using the management toolHow it works Page Technology for better business outcomes