HP Client Bridge M111 manual Field descriptions

Page 7

 

Contents

To configure the radio

3-10

Wireless mode

3-10

Restrict channels to

3-10

Antenna selection

3-11

Fast roaming threshold

 

Fast roaming delta threshold

3-11

Fast roaming threshold count

3-12

Minimum SNR threshold

3-12

Scan channel delay

3-12

Fast scan channel delay

3-12

Roaming persistence

3-12

Advanced wireless settings

3-13

RTS threshold

3-13

Transmit power control

3-13

Using station profiles to establish a wireless link

3-13

To add or edit a station profile

3-15

General

3-15

Wireless security

3-16

Quality of service

3-18

Viewing APs in the neighborhood

3-18

Field descriptions

3-19

Configuring Quality of Service (QoS)

3-19

QoS settings in a station profile

3-20

Priority mechanisms

3-20

Upstream DiffServ tagging

3-22

Creating IP QoS profiles

3-22

To define an IP QoS profile

3-22

Settings

3-23

Connecting serial devices

3-23

Serial port connector

3-24

To connect a serial device

3-24

DNS configuration

3-27

Handling unsupported traffic

3-29

To forward unsupported traffic

3-29

IP forwarding

3-30

v

Image 7
Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Regulatory information Resetting to factory defaultsViii Introduction Conventions About this guideProducts covered Important termsExample Description Commands and program listingsIntroducing the M111 Client Bridge Key featuresProfessional Installation Required Safety informationServicing Online documentation HP ProCurve Networking supportBefore contacting support Getting started Deploying the M111 Scenario 1 Connecting wired devices to a wireless networkOverview Configure your computer Configuration procedureConnect to the M111 Select Network DNS PasswordsConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Management tool About passwordsStarting the management tool Manager and Operator accounts Customizing management tool settingsPasswords Security Security policiesWeb server IP address configurationAuto-refresh To configure IP addressing Wireless range Radio configurationWireless mode To configure the radioRestrict channels to Fast roaming threshold Fast roaming delta threshold Antenna selectionMinimum SNR threshold Scan channel delayFast scan channel delay Fast roaming threshold countRTS threshold Using station profiles to establish a wireless linkAdvanced wireless settings Transmit power controlWorking with the M111 General To add or edit a station profileEAP method Wireless securityWireless protection Key sourceWorking with the M111 Ap1certificate or ap2certificate Quality of serviceViewing APs in the neighborhood Encryption typeAccess category Configuring Quality of Service QoSField descriptions Priority mechanisms QoS settings in a station profile802.1p Very-high, high, normal, low priority Differentiated Services DiffServUpstream DiffServ tagging DisabledCreating IP QoS profiles To define an IP QoS profileProtocol Start port/ End port Connecting serial devicesSettings Profile nameTo connect a serial device Serial port connectorRemote IP address Transmit timeoutIdle timeout ModeStop bits Drop wireless link when port 1 is connectedData bits Parity bitRx kbytes DNS configurationConnection time Tx kbytesServer DNS switch on server failureDynamically assigned DNS servers Override dynamically assigned DNS serversTo forward unsupported traffic DNS switch overEnable the Redirect unsupported traffic to option Handling unsupported trafficIP forwarding Cloning the address of a wired deviceLimitations Enabling Ethernet MAC cloning Wireless access to the M111 when MAC cloning is activeSelect Management Snmp Setting up management traffic interceptionManagement tool TCP port Snmp agent UDP portRemote log UDP port Using filters to restrict wireless trafficEnable the Wireless traffic filters option Snmp notifications UDP portTo assign a management address Assigning a management addressSnmp V1/v2c communities AttributesV3 users Notification receivers Managing certificates802.1X certificates 802.1X Install TLS client certificatePassword Install802.1X Manage CA certificates Certificate stores802.1X Manage TLS client certificates 802.1X Trusted CA certificatesTrusted CA certificate store Installing a new CA certificateCA certificate import formats END Certificate Certificate and private key storeSpecify the Pkcs #12 password Default installed private key/public key certificate chainsCertificate usage About certificate warnings Changing the certificate assigned to a serviceManual configuration file management Configuration file managementBackup configuration Restore configuration Reset configurationScheduled operations Software updates Enable Scheduled install Performing an immediate software updatePerforming a scheduled update Select InstallWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use GHz Operation Operation Using 5 GHz Channels in the European CommunityAntenna Band GHz Supported External Antennas5470 Indoor or outdoor use 1000 124, 128, 132, 136DGT LPD Low Power Device Statement Resetting to factory defaults Using the management tool Using the Reset buttonHow it works Page Technology for better business outcomes