HP Client Bridge M111 manual How it works, Using the Reset button, Using the management tool

Page 86

Resetting to factory defaults

How it works

Caution

How it works

Resetting the M111 to factory defaults deletes all configuration settings, resets the manager username and password to “admin”, and enables the DHCP client. If no DHCP server assigns an address to the M111, its address defaults to 192.168.1.1.

Using the Reset button

Using a tool such as a paper clip, press and hold the reset button for a few seconds until the front status lights blink three times.

Using the management tool

1.Launch the management tool (default https://<IP address of the M111>).

2.Select Maintenance > Config file management.

3.Under Reset configuration, select Reset.

B-2

Image 86

Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Resetting to factory defaults Regulatory informationViii Introduction Important terms About this guideProducts covered ConventionsCommands and program listings Example DescriptionKey features Introducing the M111 Client BridgeServicing Safety informationProfessional Installation Required Before contacting support HP ProCurve Networking supportOnline documentation Getting started Overview Scenario 1 Connecting wired devices to a wireless networkDeploying the M111 Configuration procedure Configure your computerConnect to the M111 Passwords Select Network DNSConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Starting the management tool About passwordsManagement tool Customizing management tool settings Manager and Operator accountsPasswords Security policies SecurityAuto-refresh IP address configurationWeb server To configure IP addressing Radio configuration Wireless rangeRestrict channels to To configure the radioWireless mode Antenna selection Fast roaming threshold Fast roaming delta thresholdFast roaming threshold count Scan channel delayFast scan channel delay Minimum SNR thresholdTransmit power control Using station profiles to establish a wireless linkAdvanced wireless settings RTS thresholdWorking with the M111 To add or edit a station profile GeneralKey source Wireless securityWireless protection EAP methodWorking with the M111 Encryption type Quality of serviceViewing APs in the neighborhood Ap1certificate or ap2certificateField descriptions Configuring Quality of Service QoSAccess category 802.1p QoS settings in a station profilePriority mechanisms Differentiated Services DiffServ Very-high, high, normal, low priorityTo define an IP QoS profile DisabledCreating IP QoS profiles Upstream DiffServ taggingProfile name Connecting serial devicesSettings Protocol Start port/ End portSerial port connector To connect a serial deviceMode Transmit timeoutIdle timeout Remote IP addressParity bit Drop wireless link when port 1 is connectedData bits Stop bitsTx kbytes DNS configurationConnection time Rx kbytesOverride dynamically assigned DNS servers DNS switch on server failureDynamically assigned DNS servers ServerHandling unsupported traffic DNS switch overEnable the Redirect unsupported traffic to option To forward unsupported trafficLimitations Cloning the address of a wired deviceIP forwarding Wireless access to the M111 when MAC cloning is active Enabling Ethernet MAC cloningSnmp agent UDP port Setting up management traffic interceptionManagement tool TCP port Select Management SnmpSnmp notifications UDP port Using filters to restrict wireless trafficEnable the Wireless traffic filters option Remote log UDP portAssigning a management address To assign a management addressSnmp V3 users AttributesV1/v2c communities Managing certificates Notification receiversInstall 802.1X Install TLS client certificatePassword 802.1X certificates802.1X Trusted CA certificates Certificate stores802.1X Manage TLS client certificates 802.1X Manage CA certificatesCA certificate import formats Installing a new CA certificateTrusted CA certificate store Certificate and private key store END CertificateCertificate usage Default installed private key/public key certificate chainsSpecify the Pkcs #12 password Changing the certificate assigned to a service About certificate warningsBackup configuration Configuration file managementManual configuration file management Scheduled operations Reset configurationRestore configuration Software updates Select Install Performing an immediate software updatePerforming a scheduled update Enable Scheduled installWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use Operation Using 5 GHz Channels in the European Community GHz OperationIndoor or outdoor use 1000 124, 128, 132, 136 Supported External Antennas5470 Antenna Band GHzDGT LPD Low Power Device Statement Resetting to factory defaults How it works Using the Reset buttonUsing the management tool Page Technology for better business outcomes