HP Client Bridge M111 manual Safety information, Professional Installation Required, Servicing

Page 15

Warning

Introduction

Safety information

Safety information

Professional Installation Required

Prior to installing or using an M111, consult with a professional installer trained in RF installation and knowledgeable in local regulations including building and wiring codes, safety, channel, power, indoor/outdoor restrictions, and license requirements for the intended country. It is the responsibility of the end user to ensure that installation and use comply with local safety and radio regulations.

Surge protection and grounding: If you plan on connecting an outdoor antenna to an M111, make sure that proper lightning surge protection and grounding precautions are taken according to local electrical code. Failure to do so may result in personal injury, fire, equipment damage, or a voided warranty. The HP ProCurve hardware warranty provides no protection against damage caused by static discharge or a lightning strike.

Cabling: You must use the appropriate cables, and where applicable, surge protection, for your given region. For compliance with EN55022 Class-B emissions requirements use shielded Ethernet cables.

Country of use: In some regions, you are prompted to select the country of use during setup. Once the country has been set, the M111 will automatically limit the available wireless channels, ensuring compliant operation in the selected country. Entering the incorrect country may result in illegal operation and may cause harmful interference to other systems.

Safety: Take note of the following safety information during installation:

If your network covers an area served by more than one power distribution system, be sure all safety grounds are securely interconnected.

Network cables may occasionally be subject to hazardous transient voltages (caused by lightning or disturbances in the electrical power grid).

Handle exposed metal components of the network with caution.

An M111 and all interconnected equipment must be installed indoors within the same building (except for outdoor models / antennas), including all PoE-powered network connections as described by Environment A of the IEEE 802.3af standard.

Servicing

There are no user-serviceable parts inside HP ProCurve Networking products. Any servicing, adjustment, maintenance, or repair must be performed only by trained service personnel.

1-5

Image 15

Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Regulatory information Resetting to factory defaultsViii Introduction Conventions About this guideProducts covered Important termsExample Description Commands and program listingsIntroducing the M111 Client Bridge Key featuresSafety information Professional Installation RequiredServicing HP ProCurve Networking support Online documentationBefore contacting support Getting started Scenario 1 Connecting wired devices to a wireless network Deploying the M111Overview Configure your computer Configuration procedureConnect to the M111 Select Network DNS PasswordsConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage About passwords Management toolStarting the management tool Manager and Operator accounts Customizing management tool settingsPasswords Security Security policiesIP address configuration Web serverAuto-refresh To configure IP addressing Wireless range Radio configurationTo configure the radio Wireless modeRestrict channels to Fast roaming threshold Fast roaming delta threshold Antenna selectionMinimum SNR threshold Scan channel delayFast scan channel delay Fast roaming threshold countRTS threshold Using station profiles to establish a wireless linkAdvanced wireless settings Transmit power controlWorking with the M111 General To add or edit a station profileEAP method Wireless securityWireless protection Key sourceWorking with the M111 Ap1certificate or ap2certificate Quality of serviceViewing APs in the neighborhood Encryption typeConfiguring Quality of Service QoS Access categoryField descriptions QoS settings in a station profile Priority mechanisms802.1p Very-high, high, normal, low priority Differentiated Services DiffServUpstream DiffServ tagging DisabledCreating IP QoS profiles To define an IP QoS profileProtocol Start port/ End port Connecting serial devicesSettings Profile nameTo connect a serial device Serial port connectorRemote IP address Transmit timeoutIdle timeout ModeStop bits Drop wireless link when port 1 is connectedData bits Parity bitRx kbytes DNS configurationConnection time Tx kbytesServer DNS switch on server failureDynamically assigned DNS servers Override dynamically assigned DNS serversTo forward unsupported traffic DNS switch overEnable the Redirect unsupported traffic to option Handling unsupported trafficCloning the address of a wired device IP forwardingLimitations Enabling Ethernet MAC cloning Wireless access to the M111 when MAC cloning is activeSelect Management Snmp Setting up management traffic interceptionManagement tool TCP port Snmp agent UDP portRemote log UDP port Using filters to restrict wireless trafficEnable the Wireless traffic filters option Snmp notifications UDP portTo assign a management address Assigning a management addressSnmp Attributes V1/v2c communitiesV3 users Notification receivers Managing certificates802.1X certificates 802.1X Install TLS client certificatePassword Install802.1X Manage CA certificates Certificate stores802.1X Manage TLS client certificates 802.1X Trusted CA certificatesInstalling a new CA certificate Trusted CA certificate storeCA certificate import formats END Certificate Certificate and private key storeDefault installed private key/public key certificate chains Specify the Pkcs #12 passwordCertificate usage About certificate warnings Changing the certificate assigned to a serviceConfiguration file management Manual configuration file managementBackup configuration Reset configuration Restore configurationScheduled operations Software updates Enable Scheduled install Performing an immediate software updatePerforming a scheduled update Select InstallWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use GHz Operation Operation Using 5 GHz Channels in the European CommunityAntenna Band GHz Supported External Antennas5470 Indoor or outdoor use 1000 124, 128, 132, 136DGT LPD Low Power Device Statement Resetting to factory defaults Using the Reset button Using the management toolHow it works Page Technology for better business outcomes