HP Client Bridge M111 manual Getting started

Page 29

Getting started

Scenario 3: Connecting a serial device to a wireless network

3.Under TCP connection, set Mode to Server. In this scenario, the M111 acts as a TCP server and will listen for an incoming connection from the Host computer (TCP client). Leave the other parameters at their default settings. (For more information on these settings, see TCP connection on page 3-25.)

4.Under Serial port, configure the serial parameters to match those of the serial device. This scenario assumes that the default settings are correct. For parameter descriptions see Serial port on page 3-25.

5.Select Save. The M111 will listen for a connection request from the host.

6.Check the value of State under TCP connection status. When it changes to Active, it means that the TCP connection has been established with the host, and that the point-of- sale terminal can now exchange traffic with the host.

2-13

Image 29

Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Regulatory information Resetting to factory defaultsViii Introduction Products covered About this guideImportant terms ConventionsExample Description Commands and program listingsIntroducing the M111 Client Bridge Key featuresServicing Safety informationProfessional Installation Required Before contacting support HP ProCurve Networking supportOnline documentation Getting started Overview Scenario 1 Connecting wired devices to a wireless networkDeploying the M111 Configure your computer Configuration procedureConnect to the M111 Select Network DNS PasswordsConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Starting the management tool About passwordsManagement tool Manager and Operator accounts Customizing management tool settingsPasswords Security Security policiesAuto-refresh IP address configurationWeb server To configure IP addressing Wireless range Radio configurationRestrict channels to To configure the radioWireless mode Fast roaming threshold Fast roaming delta threshold Antenna selectionFast scan channel delay Scan channel delayFast roaming threshold count Minimum SNR thresholdAdvanced wireless settings Using station profiles to establish a wireless linkTransmit power control RTS thresholdWorking with the M111 General To add or edit a station profileWireless protection Wireless securityKey source EAP methodWorking with the M111 Viewing APs in the neighborhood Quality of serviceEncryption type Ap1certificate or ap2certificateField descriptions Configuring Quality of Service QoSAccess category 802.1p QoS settings in a station profilePriority mechanisms Very-high, high, normal, low priority Differentiated Services DiffServCreating IP QoS profiles DisabledTo define an IP QoS profile Upstream DiffServ taggingSettings Connecting serial devicesProfile name Protocol Start port/ End portTo connect a serial device Serial port connectorIdle timeout Transmit timeoutMode Remote IP addressData bits Drop wireless link when port 1 is connectedParity bit Stop bitsConnection time DNS configurationTx kbytes Rx kbytesDynamically assigned DNS servers DNS switch on server failureOverride dynamically assigned DNS servers ServerEnable the Redirect unsupported traffic to option DNS switch overHandling unsupported traffic To forward unsupported trafficLimitations Cloning the address of a wired deviceIP forwarding Enabling Ethernet MAC cloning Wireless access to the M111 when MAC cloning is activeManagement tool TCP port Setting up management traffic interceptionSnmp agent UDP port Select Management SnmpEnable the Wireless traffic filters option Using filters to restrict wireless trafficSnmp notifications UDP port Remote log UDP portTo assign a management address Assigning a management addressSnmp V3 users AttributesV1/v2c communities Notification receivers Managing certificatesPassword 802.1X Install TLS client certificateInstall 802.1X certificates802.1X Manage TLS client certificates Certificate stores802.1X Trusted CA certificates 802.1X Manage CA certificatesCA certificate import formats Installing a new CA certificateTrusted CA certificate store END Certificate Certificate and private key storeCertificate usage Default installed private key/public key certificate chainsSpecify the Pkcs #12 password About certificate warnings Changing the certificate assigned to a serviceBackup configuration Configuration file managementManual configuration file management Scheduled operations Reset configurationRestore configuration Software updates Performing a scheduled update Performing an immediate software updateSelect Install Enable Scheduled installWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use GHz Operation Operation Using 5 GHz Channels in the European Community5470 Supported External AntennasIndoor or outdoor use 1000 124, 128, 132, 136 Antenna Band GHzDGT LPD Low Power Device Statement Resetting to factory defaults How it works Using the Reset buttonUsing the management tool Page Technology for better business outcomes