HP Client Bridge M111 manual Connect to the M111

Page 20

Getting started

Scenario 1: Connecting wired devices to a wireless network

B. Connect to the M111

Connect the LAN port on the computer to the Ethernet port on the M111 using a standard Ethernet cable. (If your computer has an older 10BaseT-only Ethernet interface, then use a crossover cable instead.)

 

 

 

Port

1

 

 

 

 

 

.1

 

 

 

 

 

 

 

 

 

.1

 

 

 

.168

 

LAN

port

.2

192

 

 

 

 

 

 

 

 

 

 

.1

 

 

 

 

.168

 

 

 

 

192

 

 

 

 

C. Start the M111

Power on the M111 using one of the following methods.

• A PoE-enabled switch. Various PoE-enabled switches are available from HP ProCurve.

• An HP ProCurve PoE 1-Port Power Injector (J9407A)

• An HP ProCurve MSM31x Power Supply (J9405A). This scenario uses this method. Proceed to the next step once the Power light stops blinking and remains on.

D. Connect to the management tool and login

1.Open a web browser on the computer and specify the address: https://192.168.1.1.

2.A security certificate warning is displayed the first time that you connect to the management tool. This is normal. Select whatever option is needed in your Web browser to continue to the management tool. The security warning will not appear again unless you change the IP address of the M111.

To eliminate the security warning, you need to replace the default certificate that is installed on the M111. See About certificate warnings on page 3-43.

3.On the Login page, specify admin for both Username and Password and then select Login.

4.On the License Agreement page, read and then select Accept License Agreement.

5.The Registration page appears. It is recommended that you register later by selecting Maintenance > Registration.

6.If a Country prompt appears, select the country in which the M111 will operate.

Caution

Once the country has been set, the M111 will automatically limit the available wireless

 

channels, ensuring compliant operation in the selected country. Entering the incorrect

 

country may result in illegal operation and may cause harmful interference to other

 

systems.

 

 

2-4

Image 20
Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Resetting to factory defaults Regulatory informationViii Introduction About this guide Products coveredImportant terms ConventionsCommands and program listings Example DescriptionKey features Introducing the M111 Client BridgeServicing Safety informationProfessional Installation Required Before contacting support HP ProCurve Networking supportOnline documentation Getting started Overview Scenario 1 Connecting wired devices to a wireless networkDeploying the M111 Configuration procedure Configure your computerConnect to the M111 Passwords Select Network DNSConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Starting the management tool About passwordsManagement tool Customizing management tool settings Manager and Operator accountsPasswords Security policies SecurityAuto-refresh IP address configurationWeb server To configure IP addressing Radio configuration Wireless rangeRestrict channels to To configure the radioWireless mode Antenna selection Fast roaming threshold Fast roaming delta thresholdScan channel delay Fast scan channel delayFast roaming threshold count Minimum SNR thresholdUsing station profiles to establish a wireless link Advanced wireless settingsTransmit power control RTS thresholdWorking with the M111 To add or edit a station profile GeneralWireless security Wireless protectionKey source EAP methodWorking with the M111 Quality of service Viewing APs in the neighborhoodEncryption type Ap1certificate or ap2certificateField descriptions Configuring Quality of Service QoSAccess category 802.1p QoS settings in a station profilePriority mechanisms Differentiated Services DiffServ Very-high, high, normal, low priorityDisabled Creating IP QoS profilesTo define an IP QoS profile Upstream DiffServ taggingConnecting serial devices SettingsProfile name Protocol Start port/ End portSerial port connector To connect a serial deviceTransmit timeout Idle timeoutMode Remote IP addressDrop wireless link when port 1 is connected Data bitsParity bit Stop bitsDNS configuration Connection timeTx kbytes Rx kbytesDNS switch on server failure Dynamically assigned DNS serversOverride dynamically assigned DNS servers ServerDNS switch over Enable the Redirect unsupported traffic to optionHandling unsupported traffic To forward unsupported trafficLimitations Cloning the address of a wired deviceIP forwarding Wireless access to the M111 when MAC cloning is active Enabling Ethernet MAC cloningSetting up management traffic interception Management tool TCP portSnmp agent UDP port Select Management SnmpUsing filters to restrict wireless traffic Enable the Wireless traffic filters optionSnmp notifications UDP port Remote log UDP portAssigning a management address To assign a management addressSnmp V3 users AttributesV1/v2c communities Managing certificates Notification receivers802.1X Install TLS client certificate PasswordInstall 802.1X certificatesCertificate stores 802.1X Manage TLS client certificates802.1X Trusted CA certificates 802.1X Manage CA certificatesCA certificate import formats Installing a new CA certificateTrusted CA certificate store Certificate and private key store END CertificateCertificate usage Default installed private key/public key certificate chainsSpecify the Pkcs #12 password Changing the certificate assigned to a service About certificate warningsBackup configuration Configuration file managementManual configuration file management Scheduled operations Reset configurationRestore configuration Software updates Performing an immediate software update Performing a scheduled updateSelect Install Enable Scheduled installWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use Operation Using 5 GHz Channels in the European Community GHz OperationSupported External Antennas 5470Indoor or outdoor use 1000 124, 128, 132, 136 Antenna Band GHzDGT LPD Low Power Device Statement Resetting to factory defaults How it works Using the Reset buttonUsing the management tool Page Technology for better business outcomes