HP Client Bridge M111 manual Configure MAC cloning options

Page 25

Getting started

Scenario 2: Connecting a wired device using MAC address cloning

Configuration procedure

The initial configuration steps for this scenario are the same as for Scenario 1. For each step see the instructions on the indicated page.

A. Configure your computer

See Configure your computer on page 2-3.

B. Connect to the M111

See Connect to the M111 on page 2-4.

C. Start the M111

See Start the M111 on page 2-4.

D. Connect to the management tool and login

See Connect to the management tool and login on page 2-4.

E. Set the M111 IP address

See Set the M111 IP address on page 2-5.

F.Configure a station profile

See Configure a station profile on page 2-6.

G. Configure MAC cloning options

1.Select Wireless > Bridging. The Wireless bridging page opens.

2-9

Image 25

Contents ProCurve 5400zl Switches HP ProCurve M111 Client Bridge Page HP ProCurve M111 Client Bridge Publication Number Contents Working with the M111 Field descriptions To assign a management address Regulatory information Resetting to factory defaultsViii Introduction Products covered About this guideImportant terms ConventionsExample Description Commands and program listingsIntroducing the M111 Client Bridge Key featuresProfessional Installation Required Safety informationServicing Online documentation HP ProCurve Networking supportBefore contacting support Getting started Deploying the M111 Scenario 1 Connecting wired devices to a wireless networkOverview Configure your computer Configuration procedureConnect to the M111 Select Network DNS PasswordsConfigure a station profile Connect the wired computers to the M111  The printer is configured with a static IP address Configure MAC cloning options Connect the wired device to the M111 Scenario 3 Connecting a serial device to a wireless network Configure the serial connection Getting started Getting started Working with the M111 802.1X certificates Certificate stores Certificate usage Management tool About passwordsStarting the management tool Manager and Operator accounts Customizing management tool settingsPasswords Security Security policiesWeb server IP address configurationAuto-refresh To configure IP addressing Wireless range Radio configurationWireless mode To configure the radioRestrict channels to Fast roaming threshold Fast roaming delta threshold Antenna selectionFast scan channel delay Scan channel delayFast roaming threshold count Minimum SNR thresholdAdvanced wireless settings Using station profiles to establish a wireless linkTransmit power control RTS thresholdWorking with the M111 General To add or edit a station profileWireless protection Wireless securityKey source EAP methodWorking with the M111 Viewing APs in the neighborhood Quality of serviceEncryption type Ap1certificate or ap2certificateAccess category Configuring Quality of Service QoSField descriptions Priority mechanisms QoS settings in a station profile802.1p Very-high, high, normal, low priority Differentiated Services DiffServCreating IP QoS profiles DisabledTo define an IP QoS profile Upstream DiffServ taggingSettings Connecting serial devicesProfile name Protocol Start port/ End portTo connect a serial device Serial port connectorIdle timeout Transmit timeoutMode Remote IP addressData bits Drop wireless link when port 1 is connectedParity bit Stop bitsConnection time DNS configurationTx kbytes Rx kbytesDynamically assigned DNS servers DNS switch on server failureOverride dynamically assigned DNS servers ServerEnable the Redirect unsupported traffic to option DNS switch overHandling unsupported traffic To forward unsupported trafficIP forwarding Cloning the address of a wired deviceLimitations Enabling Ethernet MAC cloning Wireless access to the M111 when MAC cloning is activeManagement tool TCP port Setting up management traffic interceptionSnmp agent UDP port Select Management SnmpEnable the Wireless traffic filters option Using filters to restrict wireless trafficSnmp notifications UDP port Remote log UDP portTo assign a management address Assigning a management addressSnmp V1/v2c communities AttributesV3 users Notification receivers Managing certificatesPassword 802.1X Install TLS client certificateInstall 802.1X certificates802.1X Manage TLS client certificates Certificate stores802.1X Trusted CA certificates 802.1X Manage CA certificatesTrusted CA certificate store Installing a new CA certificateCA certificate import formats END Certificate Certificate and private key storeSpecify the Pkcs #12 password Default installed private key/public key certificate chainsCertificate usage About certificate warnings Changing the certificate assigned to a serviceManual configuration file management Configuration file managementBackup configuration Restore configuration Reset configurationScheduled operations Software updates Performing a scheduled update Performing an immediate software updateSelect Install Enable Scheduled installWorking with the M111 Regulatory information Manufacturers FCC Declaration of Conformity Statement Countries of Operation & Conditions of Use GHz Operation Operation Using 5 GHz Channels in the European Community5470 Supported External AntennasIndoor or outdoor use 1000 124, 128, 132, 136 Antenna Band GHzDGT LPD Low Power Device Statement Resetting to factory defaults Using the management tool Using the Reset buttonHow it works Page Technology for better business outcomes