76
To Customers
Cautions in using the remote controller
1.After all the power supplies of the air conditioner have been turned on, turn on the power supply of the central remote controller.
If the power supplies of the air conditioner and the remote controller are turned on at the same time, or if they are turned on in reverse order, the check code [97] may be temporarily displayed on the central remote controller. When the connection cabling and setup of the central address are correct, the connected air conditioner is displayed on the central remote controller.
2.As described below, there are differences of the display on LCD and the individual restrictions for the operation in the handy remote controller
|
| Contents |
|
|
|
|
|
| ||
| Item |
|
|
| Cautions |
|
|
| ||
| Main | Central |
|
|
|
| ||||
|
|
|
|
|
|
|
| |||
|
| remote controller | remote controller |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
1 | Fan speed select |
|
| Display of air speed selection differs. |
|
|
| |||
|
|
|
|
|
| |||||
|
|
|
| When operating the main remote controller, | is not displayed. | |||||
2 | Fan speed select |
|
| If selecting | at the central side, | is displayed on the main | ||||
| in FAN mode |
|
| remote controller. |
|
|
|
| ||
|
|
|
| In this time, the air speed is . |
|
|
|
| ||
|
|
|
|
|
| |||||
3 | Fan speed select |
|
| only is displayed on the central remote controller. | is | |||||
|
| displayed on the main remote controller even by change of the | ||||||||
in DRY mode |
|
| ||||||||
|
|
| setup temperature/louver, and the air speed changes automatically. | |||||||
|
|
|
| |||||||
|
|
|
|
| ||||||
|
|
| [LOUVER] | [LOUVER] only is displayed on the central remote controller. | ||||||
| Air direction | and air direction | [LOUVER] is displayed when the flap is swinging, and ON and | |||||||
4 |
| OFF of the swing operation set to the louver are exchanged. | ||||||||
adjustment | adjustment |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| |||||
|
| (No display) | [LOUVER] Manual | Set the air direction on the main remote controller. |
| |||||
|
|
|
|
|
| |||||
|
|
|
| In case of type without function of air direction adjustment |
| |||||
|
| Test run | Display of check | The function differs when the | button is pushed for a long time. | |||||
5 | Check button | code and Check | If the central remote | |||||||
(4 seconds) | ||||||||||
|
| reset (3 seconds) | air conditioner, the operation stops temporarily, and then the | |||||||
|
|
| ||||||||
|
|
|
| operation is resumed. (Trouble of the air conditioner is cleared.) | ||||||
|
|
|
|
|
|
|
| |||
|
| Display with 3 digits | Display with 2 digits | The display of the check code differs. |
|
|
| |||
6 | Check code |
|
|
|
|
|
| |||
(Alphabet + 2 digits | (Alphabet or | Ex.) Float switch operation |
|
|
|
| ||||
|
| numerals) | numerals) | Main side : [P10], Collective side : [0b] |
|
| ||||
|
|
|
|
|
|
|
|
|
|
3.When using the remote controller with the former remote controller
|
| Contents |
| |
| Item |
|
| Remarks |
| New remote | Former remote | ||
|
| controller | controller |
|
|
|
| ||
|
|
|
|
|
1 | (No display) | (No display) | All the setups and Start/Stop operation are available. | |
|
|
|
|
|
2 | Center |
| CENTER | The setup contents of the central remote controller are fixed, and |
| the Start/Stop operation and timer operation are available on the | |||
| goes on. | |||
|
|
| main remote controller. | |
|
| CENTER |
| |
|
|
|
| |
|
| goes on. | CENTER | The setup contents of the central remote controller are fixed, and |
|
|
| ||
3 | Locked |
| the air conditioner stops. The operation on the main remote | |
| flashes. | |||
|
|
| controller is unavailable. | |
|
|
|
| |
|
|
|
|
|
* Before using the remote controller, read the Owner’s Manual thoroughly to use it correctly.