HP XA manual 10BT/100TX LAN Features, Remote Power On, Supporting RPO

Page 62

3 Interface Devices and Mass-Storage Drives

10BT/100TX LAN Controller

10BT/100TX LAN Features

Feature:

Description:

 

 

LAN Controller

AMD PCNET-Fast chip

 

 

RJ45 Connector

10BT/100TX autonegotiation

 

 

Remote Boot

Protocols integrated in System BIOS

 

 

ExtStart Connector

Connection to CPU board

 

LAN remote power on signals

 

 

Remote Power On

Full remote power on with Magic Packet

 

 

Remote Wake Up

Wake Up from Suspend state with Magic Packet

 

 

Remote Power On

Remote Power On (RPO) is available at 10 and 100 Mbits per second.

Vstandby requirements The Vstandby requirements for HP network cards supporting RPO, is:

supporting RPO

• A power supply able to deliver at least 250mA on Vstandby output. This is the case for all HP Kayak systems.

Optional Bootrom Socket It is possible to add a flash device on the network card socket with a specific LAN bootrom code. This new bootrom code will be seen and mapped automatically by the system BIOS instead of the embedded version (system BIOS).

NOTE

At the time this TRM was produced, there was no flashing tool available to

 

allow you to update the bootrom content in the flash on the LAN adapter. A

 

flashing tool for any AMD based card may be available, but in order to use this

 

tool on HP cards, only 29fxxx flash devices must be used. At present, no test

 

has been carried out using this tool on HP cards.

 

 

Flash / ROM Devices

The 10BT/100TX card provides a PLCC 32-pin socket and any size of flash

 

device can be used up to 256KB§.

62

Image 62
Contents Technical Reference Manual Hardware and Bios Page Preface Bibliography How to use this online guide Page Contents Interface Devices and Mass-Storage Drives HP Bios Power-On Self-Test and Error Messages System Overview Rear view Package for the Desktop ModelsFront view System Overview Package for the Desktop ModelsPackage for the Minitower Models HP Kayak XA PC Workstation Overview System Overview Hardware Control Panel Hardware Control PanelMinitower Hardware Control Panel Electrical Specifications Specifications and Characteristic DataPhysical Characteristics Min Safety StandardEfficiency Max 11.0Max Current at +5 Voltage range 90-140Maximum input current +3.3 V and +5 Current at -5 Current at +5V standbyDesktop Parameter Total Rating Current at +12 Current at -12Environmental Specifications Desktop and Minitower Access HP World Wide Web DocumentationWhere to Find the Information Routines Post GuideSystem board Peripheral DevicesSystem Overview Documentation System Board System Board and Backplane Boards System Board System Board and Backplane BoardsDesktop Backplane PCI Mapping Table Device DesktopBackplane front view PCI Device Slot#Not used Architectural View System Board Architectural ViewPL Bus Interface Chip-SetPAC Chip 440LX PCI Bus InterfaceSystem Clocking AGP Bus InterfaceRead/Write Buffers Main Memory ControllerPIIX4, PCI/ISA Bridge Chip 82371AB Second Level CacheIDE Controller ISA Bus InterfaceSMBus Controller USB ControllerCache Memory Counter / TimerSerial Eeprom System Board Devices on the Processor-Local Bus Devices on the Processor-Local BusIntel Pentium II Microprocessor Plastic clips Bracket pillars Heat sink Local Bus SwitchBus Frequencies System Board Main Memory Bus Error Correcting Code OperationMain Memory Bus PCI Device Devices on the PCI BusIntegrated Drive Electronics IDE Name NumberPlug and Play Other PCI Accessory DevicesUniversal Serial Bus USB Controller Accelerated Graphics Port AGP Controller System Board Accelerated Graphics Port AGP ControllerDevice PCI Bus # Pentium II Processor 66 MHz System Board Devices on the SM Bus Devices on the SM BusSerial Eeprom Device SM Bus AddressLM75 Chip Main PLLSerial / parallel Devices on the ISA BusSuper I/O Controller NS ControllerAudio Controller SpecificationsFeature Description Host InterfaceFlash Eeprom Closed System Board SwitchesSwitch Switch Function Default OpenBios Update Crisis Recovery Procedure Updating the system Little BenOther ISA Accessory Devices Check the accessory board’s documentation if you are unsureSystem Board Devices on the ISA Bus Interface Devices and Mass-Storage Drives Cirrus 5465 Graphics Controller Chip Page Connectors Video MemoryRefresh rates Available Video ResolutionsResolution 640 60, 75, 85 Hz 800Scsi / LAN Combo Board PCI InterfaceConnector Description Location 10BT/100TX PCI LAN ConnectorUltra wide 16-bit Scsi connector Scsi InterfaceInterface Features PCI Interface External 8-bit Scsi connectorScsi / PCI LAN Combo Board Features Scsi Interface10BT/100TX LAN Controller Supporting RPO 10BT/100TX LAN FeaturesRemote Power On Installing Two LAN Remote Power On Cards Flexible Disk Drives Mass-Storage DrivesHard Disk Drives Buffer Memory Size Kbytes Features Panasonic CD-ROM CD-585-BCD-ROM Drives Status Panel Connector Pin Signal Connectors and SocketsIDE Connector Pin Signal Flexible Disk Drive Data Connector Pin SignalExtStart Connector Bit Scsi Connector Bit Scsi Connector Pin SignalAUX Connector Pin Signal CD Audio Connector Pin SignalPin Signal Package Intrusion J8VGA DB Connector Pins Standard VGA Vesa Pass-Through ConnectorVGA Connector Socket Pin LayoutsPage HP Bios HP/Phoenix Bios Summary HP/Phoenix Bios SummaryUsing the HP Setup Program Advanced Menu Security Default Settings You Can Change Symbios Logic Scsi Configuration UtilityStarting the Scsi Configuration Utility Soft Power Down Power Saving and ErgonometryPower-On from Space-Bar Bios Addresses System Memory MapHP I/O Port Map I/O Addresses Used by the System1 Address Ports FunctionDMA controller Interrupt Request Description HP Bios Power-On Self-Test and Error Messages For example, if the error 0101 52 is displayed Order in Which the Tests are PerformedPost Routine Description Code Post Routine Description Post Routine Description Detect and install external parallel ports Detect and install external RS 232 portsConfigure non-MCD IDE controllers Configure Motherboard Configurable DevicesPost done prepare to boot operating system Enter SetupCheck for errors Terminate QuietBootFollowing are for boot block in Flash ROM F1= Continue, F2= Setup, Enter= View System Error Error Message SummaryPower-On Self-Test and Error Messages Error Message Summary Enter= View System ErrorCause / Symptom 0512h HDD # 2 self-test error 0510h HDD # 0 self-test error0511h HDD # 1 self-test error 0513h HDD # 3 self-test errorMessage Beep Codes Beep PatternLights on the Hardware Control Panel Appendix Video Modes Standard VGA ModesType Refresh MHz Extended Video ModesColors 94.5 44.978.7 102135 108126 157162 104Refresh Mode Bios Modes SupportedResolution MHz DAC Maximum Refresh Rates106 6001024 107 Type1200 Appendix Video Modes 108