York DJ150 Unit Voltage Limitations, Rigging and Handling, Unit Temperature Limitations, Location

Page 11

035-19046-002-B-0104

TABLE 1: UNIT VOLTAGE LIMITATIONS

Power Rating*

Minimum

Maximum

208/230-3-60

187

252

 

 

 

460-3-60

432

504

 

 

 

575-3-60

540

630

 

 

 

*. Utilization range “A” in accordance with ARI Standard 110.

RIGGING AND HANDLING

Exercise care when moving the unit. Do not remove any packaging until the unit is near the place of installation. Rig the unit by attaching chain or cable slings to the lifting holes provided in the base rails. Spreader bars, whose length exceeds the largest dimension across the unit, MUST be used across the top of the unit.

TABLE 2: UNIT TEMPERATURE LIMITATIONS

Temperature

Min.

Max.

 

 

 

Wet Bulb Temperature (°F) of Air on

57

72

Evaporator Coil

 

 

 

 

 

Dry Bulb Temperature (°F) of Air on

0*

125

Condenser Coil

 

 

 

 

 

*. A low ambient accessory is available for operation down to -20°F.

LOCATION

Use the following guidelines to select a suitable location for these units:

1.Unit is designed for outdoor installation only.

2.Condenser coils must have an unlimited supply of air. Where a choice of location is possible, position the unit on either north or east side of building.

3.Suitable for mounting on roof curb.

4.For ground level installation, use a level concrete slab with a minimum thickness of 4 inches. The length and width should be at least 6 inches greater than the unit base rails. Do not tie slab to the building foundation.

5.Roof structures must be able to support the weight of the unit and its options/accessories. Unit must be installed on a solid, level roof curb or appropriate angle iron frame.

6.Maintain level tolerance to 1/2” across the entire width and length of unit.

Excessive exposure of this furnace to contaminated combustion air may result in equipment damage or personal injury. Typical contaminates include: per- manent wave solution, chlorinated waxes and clean- ers, chlorine based swimming pool chemicals, water softening chemicals, carbon tetrachloride, Halogen type refrigerants, cleaning solvents (e.g. perchloro- ethylene), printing inks, paint removers, varnishes, hydrochloric acid, cements and glues, antistatic fab- ric softeners for clothes dryers, masonry acid wash- ing materials.

If a unit is to be installed on a roof curb other than a YORK roof curb, gasketing must be applied to all surfaces that come in contact with the unit under- side.

Before lifting, make sure the unit weight is distrib- uted equally on the rigging cables so it will lift evenly.

Units may be moved or lifted with a forklift. Slotted openings in the base rails are provided for this purpose.

LENGTH OF FORKS MUST BE A MINIMUM OF 60 INCHES.

All panels must be secured in place when the unit is lifted.

The condenser coils should be protected from rig- ging cable damage with plywood or other suitable material.

FRONT

LEFT

C

B

A

D

FIGURE 4 - UNIT 4 POINT LOAD

Unitary Products Group

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Installation Manual Table of Contents List of Tables List of FiguresInspection Safety ConsiderationsGeneral Renewal Parts ReferenceApprovals Nomenclature 12½ Ton Predator Model Number Nomenclature 150 N15NOMENCLATURE, Additional Options Preceding Installation InstallationInstallation Safety Information Limitations Compressor SectionPREDATOR Magnum Component Location Location Unit Temperature LimitationsUnit Voltage Limitations Rigging and HandlingClearances Unit WeightsPoint Load Weight Detail C Unit DimensionsBottom Duct Openings from Above Duct Covers Rear Duct Dimensions DuctworkPREDATOR Magnum Roof Curb Dimensions Filters Thermostat WiringControl Wire Sizes Power and Control WiringElectronic Thermostat Field Wiring Power Wiring DetailField Wiring 24 Volt Thermostat Contactor 1M Factory or Field Ground MCA Minimum Supply AIR CFM Physical DataOptional Electric Heat GAS Piping Optional GAS HeatGAS Heat Application Data LP UNITS, Tanks and Piping GAS ConnectionFactory Installed Options Field Installed Accessories Indoor AIR Quality AQ Minimum Position AdjustmentEnthalpy SET Point Adjustment Enthalpy SET Point Chart Belt Tension PhasingBlower Rotation Supply AIR LimitationsTurns Open ESP‡ CFM BHP Blower performance includes dry coil and two-inch Method ONE Indoor Blower SpecificationsAIR Balance Checking AIR QuantityDRY Coil Delta P Supply AIR Drive Adjustment Cooling Sequence of Operation OperationAdditional Static Resistance Motor Sheave Datum DiametersNo Outdoor AIR Options Economizer Single or Dual with Power ExhaustCooling Operation Errors HIGH-PRESSURE Limit SwitchCompressor Protection Safety ControlsElectric Heat Anticipator Setpoints Electric Heating Operation ErrorsElectric Heat Limit Setting Electric Heating Sequence of OperationsIgnition Control Board GAS Heating Operation ErrorsGAS Heating Sequence of Operations GAS Heat Limit Control Settings START-UP GAS Heat START-UP CoolingChecking GAS Input Post Start ChecklistManifold GAS Pressure Adjustment Shut DownGAS Rate Cubic Feet PER Hour BURNERS/ORIFICES INSPECTION/SERVICING Adjustment of Temperature RiseUnit Control Board Flash Codes TroubleshootingCharging the Unit PREDATOR Magnum Flash CodesBasic Troubleshooting Flowchart Trip Failure Flow Chart Cooling Troubleshooting Guide Unitary Products Group 035-19046-002-B-0104 GAS Heat Troubleshooting Guide Unitary Products Group 035-19046-002-B-0104 Unitary Products Group Unitary 5005 Norman Products York Group Drive 73069

DJ150 specifications

The York DJ150 is a standout model in the world of portable DJ equipment, designed to cater to both budding DJs and seasoned professionals. Its sleek and compact form factor makes it highly portable, allowing for easy transporting to gigs, parties, or personal events.

One of the main features of the DJ150 is its user-friendly interface, which includes a simplified control layout. This design boils down essential functions into accessible buttons and knobs, enabling DJs to focus on their mixes without distractions. The large jog wheels are not only responsive but also provide precision when scratching and cueing tracks, making it a joy to use for both live performances and practice sessions.

In terms of sound quality, the York DJ150 is equipped with high-performance audio circuitry. It ensures that sound clarity is maintained, with a dynamic range that captures the intricacies of music. The device supports multiple audio formats, offering versatility for DJs that work with various types of digital music files.

The DJ150 integrates advanced technologies that facilitate seamless mixing and creative expression. With features such as built-in sound effects, loops, and samples, DJs can add their personal touch to sets. Additionally, the model includes an intelligent beat matching function which automatically syncs the tempo of different tracks, allowing for smooth transitions and uninterrupted flow.

Connectivity is another strong point for the York DJ150. It offers multiple input and output options, including USB ports for quick connections to a laptop or external devices, line inputs for instruments or microphones, and headphones output for monitoring. This ensures that users can connect a wide range of equipment while maintaining a clean setup.

Durability plays a key role in the DJ150's design, as it is built to withstand the rigors of frequent use. Its robust construction and quality materials contribute to its longevity, appealing to those who value reliable gear.

In conclusion, the York DJ150 represents a versatile solution for DJs seeking a blend of portability, functionality, and sound quality. Its comprehensive features and professional-grade technologies position it as a strong contender in the DJ equipment market, making it suitable for performances of all levels. Whether you are a novice starting your DJ journey or a seasoned pro looking for an efficient tool, the DJ150 ticks all the boxes.
Top Page Image Contents