York DJ150 installation manual Power Wiring Detail, Electronic Thermostat Field Wiring

Page 18

035-19046-002-B-0104

The internal wiring harnesses furnished with this unit are an integral part of the design certified unit. Field alteration to comply with electrical codes should not be required. If any of the wire supplied with the unit must be replaced, replacement wire must be of the type shown on the wiring diagram and the same minimum gauge as the replaced wire.

A disconnect must be utilized for these units. Factory installed disconnects are available. If installing a disconnect

(field supplied or York Internationalsupplied accessory), refer to Figure 3 for the recommended mounting location.

Avoid damage to internal components if drilling holes for disconnect mounting.

NOTE: Since not all local codes allow the mounting of a dis- connect on the unit, please confirm compliance with local code before mounting a disconnect on the unit.

Electrical line must be sized properly to carry the load. USE COPPER CONDUCTORS ONLY. Each unit must be wired with a separate branch circuit fed directly from the meter panel and properly fused.

Refer to Figures 16, 17 and 18 for typical field wiring and to the appropriate unit wiring diagram mounted inside control doors for control circuit and power wiring information.

When connecting electrical power and control wiring to the unit, water-proof connectors must be used so that water or moisture cannot be drawn into the unit during normal operation. The above water-proofing conditions will also apply when installing a field sup- plied disconnect switch.

POWER WIRING DETAIL

Units are factory wired for the voltage shown on the unit nameplate. Refer to Electrical Data Tables 8 and 9 to size power wiring, fuses, and disconnect switch.

Power wiring is brought into the unit through the side of the unit or the basepan inside the curb.

THERMOSTAT1

TERMINALS

RC

RH

Y1

Y2

W1

W2

G

C

X1

X3

2

X4

A1

A2

T

T

TOREMOTESENSOR 2ET04701324IFUSED

UNITTERMINALS

STRIPTB1

R

Y1

Y2

W1

W2

G

C

24Volt

XTransformer

OCC

1ElectronicprogrammableThermostat2ET0770010024(includessubbase).

2TerminalsA1andA2providearelayoutputtoclosetheoutdoor economizerdamperswhenthethermostatswitchestotheset-backposition.

FIGURE 16 - ELECTRONIC THERMOSTAT FIELD WIRING

18

Unitary Products Group

Image 18
Contents Installation Manual Table of Contents List of Figures List of TablesSafety Considerations GeneralInspection Reference ApprovalsRenewal Parts 12½ Ton Predator Model Number Nomenclature 150 N15 NomenclatureNOMENCLATURE, Additional Options Installation Installation Safety InformationPreceding Installation Compressor Section LimitationsPREDATOR Magnum Component Location Rigging and Handling Unit Temperature LimitationsUnit Voltage Limitations LocationUnit Weights Point Load WeightClearances Unit Dimensions Detail CBottom Duct Openings from Above Rear Duct Dimensions Ductwork Duct CoversPREDATOR Magnum Roof Curb Dimensions Power and Control Wiring Thermostat WiringControl Wire Sizes FiltersPower Wiring Detail Electronic Thermostat Field WiringField Wiring 24 Volt Thermostat Contactor 1M Factory or Field Ground MCA Physical Data Optional Electric HeatMinimum Supply AIR CFM Optional GAS Heat GAS Heat Application DataGAS Piping GAS Connection LP UNITS, Tanks and PipingFactory Installed Options Field Installed Accessories Minimum Position Adjustment Enthalpy SET Point AdjustmentIndoor AIR Quality AQ Enthalpy SET Point Chart Supply AIR Limitations PhasingBlower Rotation Belt TensionTurns Open ESP‡ CFM BHP Blower performance includes dry coil and two-inch Checking AIR Quantity Indoor Blower SpecificationsAIR Balance Method ONEDRY Coil Delta P Supply AIR Drive Adjustment Motor Sheave Datum Diameters OperationAdditional Static Resistance Cooling Sequence of OperationHIGH-PRESSURE Limit Switch Economizer Single or Dual with Power ExhaustCooling Operation Errors No Outdoor AIR OptionsSafety Controls Compressor ProtectionElectric Heating Sequence of Operations Electric Heating Operation ErrorsElectric Heat Limit Setting Electric Heat Anticipator SetpointsGAS Heating Operation Errors GAS Heating Sequence of OperationsIgnition Control Board GAS Heat Limit Control Settings START-UP Cooling START-UP GAS HeatShut Down Post Start ChecklistManifold GAS Pressure Adjustment Checking GAS InputGAS Rate Cubic Feet PER Hour Adjustment of Temperature Rise BURNERS/ORIFICES INSPECTION/SERVICINGPREDATOR Magnum Flash Codes TroubleshootingCharging the Unit Unit Control Board Flash CodesBasic Troubleshooting Flowchart Trip Failure Flow Chart Cooling Troubleshooting Guide Unitary Products Group 035-19046-002-B-0104 GAS Heat Troubleshooting Guide Unitary Products Group 035-19046-002-B-0104 Unitary Products Group Unitary 5005 Norman Products York Group Drive 73069

DJ150 specifications

The York DJ150 is a standout model in the world of portable DJ equipment, designed to cater to both budding DJs and seasoned professionals. Its sleek and compact form factor makes it highly portable, allowing for easy transporting to gigs, parties, or personal events.

One of the main features of the DJ150 is its user-friendly interface, which includes a simplified control layout. This design boils down essential functions into accessible buttons and knobs, enabling DJs to focus on their mixes without distractions. The large jog wheels are not only responsive but also provide precision when scratching and cueing tracks, making it a joy to use for both live performances and practice sessions.

In terms of sound quality, the York DJ150 is equipped with high-performance audio circuitry. It ensures that sound clarity is maintained, with a dynamic range that captures the intricacies of music. The device supports multiple audio formats, offering versatility for DJs that work with various types of digital music files.

The DJ150 integrates advanced technologies that facilitate seamless mixing and creative expression. With features such as built-in sound effects, loops, and samples, DJs can add their personal touch to sets. Additionally, the model includes an intelligent beat matching function which automatically syncs the tempo of different tracks, allowing for smooth transitions and uninterrupted flow.

Connectivity is another strong point for the York DJ150. It offers multiple input and output options, including USB ports for quick connections to a laptop or external devices, line inputs for instruments or microphones, and headphones output for monitoring. This ensures that users can connect a wide range of equipment while maintaining a clean setup.

Durability plays a key role in the DJ150's design, as it is built to withstand the rigors of frequent use. Its robust construction and quality materials contribute to its longevity, appealing to those who value reliable gear.

In conclusion, the York DJ150 represents a versatile solution for DJs seeking a blend of portability, functionality, and sound quality. Its comprehensive features and professional-grade technologies position it as a strong contender in the DJ equipment market, making it suitable for performances of all levels. Whether you are a novice starting your DJ journey or a seasoned pro looking for an efficient tool, the DJ150 ticks all the boxes.